Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
BHP1518
5
*
NR 17CW185
3.6) Bending procedure (
LED
60°
During the bending operation, keep your hands well away from the
6
ON
*
moving ram. Risk of crushing.
max 90°
The bending process must be activated using the bending tool's control button.
RESET
Do not use the control button (1) on-board the pump!
7
SW:S1K16500
BATTERY
Press the control button (13) on the tool and keep it pressed down until
the motor switches off automatically.
When the motor switches off, release the button (13).
BATTERY
The bending operation is considered finished when the motor switches
off automatically and the tool's piston has returned to its starting position.
In case of emergency, it is possible immediately interrupt the bending
P
= 729 bar
n
process at any moment during the cycle by releasing the button (13)
P =
0 bar
and the tool's ram will return to its starting position.
RESET
P
= 729 bar
n
SW:S1J41405
P
= 731 bar
p
The "ERROR" message on the display (along with an audible signal),
P
= 729 bar
n
90°
indicates that the pump has reached the maximum developed pressure
OK
but it was not possible to obtain the bend angle set on the tool.
P = 0 bar
Check the correct setting of the bending tool.
At the end of the operation, before disconnecting the hose, check that the ram of the
P
= 325 bar
p
attached tool is fully retracted.
max.
P
= 155 bar
n
ar
P = 0 bar
1
P =
0 bar
*
NOTE: For work needs, it is possible to perform an expansion
BATTERY
cycle without disconnect the cable from the connector (9),
in this case it is essential to change the operating mode
P
= 2248 psi
n
bar
P
through the diplay (Ref. to § 4.2 for further details).
= 105 bar
p
2
*
P =
0 psi
3
*
BATTERY
To return in bending mode change another time the operating
mode on the display.
10
4
*
29990
BHP1518
5
*
NR 17CW185
25
LED 60°
6
*
P
Ref. to Fig. 6)
p
BATTERY
ERROR
BATTERY
30001
30001
BATTERY
RESET
BATTERY
SW:S1J41405
30001
90°
RESET
max 90°
max 90°
SW:S1J41405
P =
0 bar
90°
max 90°
P
= 547 bar
p
max.
min.
max.
BATTERY
BATTERY
BATTERY
LED
ON
LED
OFF
BEEP
P = 0 bar
P
= 105 bar
p
P
= 2248 psi
n
2
*
P =
= 105 bar
3
*
BATTERY
4
*
ERROR
BHP1518
5
*
NR 17CW185
001
001
LED
60°
002
002
6
ON
*
ERROR
003
003
001
RESET
7
004
004
SW:S1K16500
002
003
004
P
= 155 bar
n
P =
min.
min.
P
= 155 bar
n
BATTERY
P
= 157 bar
p
BATTERY
LED
OFF
LED
P
= 155 bar
ON
n
BEEP
OK
BEEP
BATTERY
0 psi
10
29990
90°
90°
max 90°
max 90°
-15°
-15°
max 90°
max 90°
max 90°
BATTERY
BATTERY
P
= 155 bar
n
0 bar
P =
0 bar
30001
P
= 155 bar
n
P
= 157 bar
p
RESET
SW:S1J41405
P
= 155 bar
n
OK
90°
max 90°
max.
BEEP
BATTERY
BATTERY
BATTERY
P = 0 bar
P
= 105 bar
p
BEEP
ERROR
001
002
003
004
9
min.
Publicité
Table des Matières
