Technical Data; Declaration Of Conformity; Safety Instructions - Wolf 017815 ab Mode D'emploi

1.0 Technical data

Power supply . . . . . . . . . . . . . . . . . . . . . . . . . .230V AC (110V)
Power consumption . . . . . . . . . . . . . . . . . . . . . . .710W (600W)
Speed (No-load operat) . . . . . . . . . . . . . . . . . . . . .10.000 r.p.m.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5,4 kg
Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . .108 dB(A)
Sound energy level . . . . . . . . . . . . . . . . . . . . . . . . . .121 dB(A)
Hand/Arm-Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . .12,5 m/s
Material thickness . . . . . . . . . . . . . . . . . . . . . . . . . . .up to 6 mm
Stripe width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 to 35 cm
Grooving blade . . . . . . . . . . . . . . . . . . . . . . . . .tungsten tipped
diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 mm
thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,3 mm
tooth number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
2.0

Declaration of conformity

We declare under our sole responsibility that this product is
in conformity with the following standards of standardization
documents: EN 50 144, according to the provisions of the
Directives 73/23/EWG, 89/336/EWG 98/37 EG
05
Dipl.-Ing. (FH) Dieter Hammel
Konstruktionsleitung
i.V.
Uzin Utz

3.0 Safety instructions

Disconnect power supply before doing any maintenance at the
machine. Use only faultless sharpened blades that are appro-
priate for your application. Maintenance only by qualified per-
sonnel. Use only genuine spare parts.
Every machine comes with goggles and ear protection. Please
use them for your own safety! The machine may only be operated
with dust bag or with dust collection by vacuum cleaner.
3.1 Introduction
This operating manual helps you to become familiar with the
Stripe Cutter for your maximum benefit. You get helpful information
to realize and avoid danger.
Thus you do not only improve your own safety, but decrease
repair costs and extend the durability of your machine. This
operating manual must be read in any case before starting work
with the machine. Also maintenance personnel must have read
and understood the instructions.
3.2 Danger while working with the machine
The Stripe Cutter is designed to the state of the art and the current
technical standards. Nevertheless its usage could cause danger
for life or material values. Disturbances that could impair safety,
have to be eliminated at once.
Tools| D-74360 Ilsfeld |
Comes with:
Stripe Cutter LS35
handle
ear protection
goggles
dust bag with shackle
2
operating manual
Ungerhalde 1
While working with the stripe cutter always wear goggles
and ear protection. Otherwise you are in danger of inju-
ring your eyes by parts flying about. Furthermore you
are in danger of injuring your ears by noise.
Use this machine only:
for the defined application
in a technically perfect condition
04/2004 Fugenfräse
7