Bosch GST 700 Professional Notice Originale page 7

A)
(21) Circle cutter centring tip
Technical Data
Jigsaw
Article number
Rated power input
No-load stroke rate n
0
Stroke
Max. cutting depth
– In wood
– In aluminium
– In steel (unalloyed)
Max. cutting angle (left/right)
Weight according to EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions. Only use saw blades
with single lug shank (T shank). The saw blade should not be
longer than required for the intended cut.
Use a narrow saw blade when sawing tight curves.
Inserting the saw blade (see figure A)
Clean the shaft on the saw blade before inserting it.
u
A dirty shaft cannot be securely fixed in place.
Push the saw blade (11), with the teeth in the cutting direc-
tion, into the saw blade receptacle (9) until it clicks into
place.
Make sure when inserting the saw blade that the back of the
saw blade is in the groove on the guide roller (10).
Check that the saw blade is seated securely. A loose
u
saw blade can fall out and lead to injuries.
Removing the saw blade (see figure B)
Push the saw blade receptacle (9) upwards in the direction
of the arrow and remove the saw blade (11).
Anti-splinter guard (see figure C)
The anti-splinter guard (15) (accessory) can prevent splin-
tering of the surface while sawing wood. The anti-splinter
Bosch Power Tools
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GST 700
3 601 BA7 0..
W 500
−1
min 1450–3200
mm
mm
mm
mm
°
kg 2.1
guard can only be used with certain saw blade types and only
at a cutting angle of 0°.
Push the anti-splinter guard (15) into the base plate (7)
from below.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Hood
Fit the hood (13) before you connect the power tool to the
dust extraction system.
Position the hood (13) on the power tool so that the brack-
ets click into place in the recesses on the housing.
Remove the hood (13) when working without a dust extrac-
tion system and for mitre cuts. To do this, push the hood to-
gether at the level of the outer brackets and remove it by
pulling it forwards.
English | 7
GST 700
3 601 BA7 0C.
500
1700–3300
20 20
70 70
10 10
6 6
45 45
2.1
/ II / II
1 609 92A 5T7 | (10.06.2020)