Battery Charger - Stiga BT 48 Li 2.0 Manuel D'utilisation

Masquer les pouces Voir aussi pour BT 48 Li 2.0:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3
EN
· If a leak develops, the released electrolytes are
corrosive and toxic. DO NOT get the solution in the
eyes or on skin, and do not swallow it.
DO NOT place these batteries in your regular
household trash.
· DO NOT incinerate.
· DO NOT place them where they will become part of
any waste landfill or municipal solid waste stream.
· Take them to a certified recycling or disposal centre.

2. Battery Charger

SPECIFICATIONS
48V charger: CG 48 Li
Input: 220-240V a.c. 50 Hz, 1.1A Max
Output: 48V d.c. 1.5A
CHARGING PROCEDURE
NOTE: The battery is not shipped fully charged. It is
recommended to fully charge before use to ensure that
maximum run time can be achieved. This lithium-ion
battery will not develop a memory and may be charged
at any time.
1. Plug the charger into an AC power outlet.
2. Insert the battery pack (1) into the charger (2).
3
2
This is a diagnostic charger. The Charger LED Lights (3)
will illuminate in specific order to communicate the
current battery status. They are as follows:
CHARGING PROCEDURE (LED INDICATOR )
BATTERY IS CHARGING:
FULL CHARGED:
BATTERY IS TOO WARM OR TOO COLD:
(REMOVE FOR APPROX.30 MINUTES TO ALLOW
TO COOL)
NO BATTERY PRESENT:
DEFECTIVE BATTERY:
(REMOVE AND REPLACE WITH NEW BATTERY
IF THIS OCCURS)
False Defect Note:
WARNING
1
GREEN
BLINKING
GREEN
RED
OFF
RED
BLINKING
BATTERY / BATTERY CHARGER
When the battery is inserted into the charger, and the
status LED flashes, remove the battery from the charger
for 1 minute, then reinsert. If the status LED indicates
normal than the battery pack is good. If the status LED
is still blinking, remove the battery pack and unplug the
charger. Wait 1 minute and plug the charger back in
and reinsert the battery pack. If the status LED indicates
normal than the battery pack is good. If the status LED is
still blinking then the battery pack is defective and needs
to be replaced.
NOTE: When the red indictor flickers, pull out the battery
from the charger and insert again within 2 hours. If the
indictor shows charging, that means the battery is good.
After 2 hours, please pull out the battery and also pull
out the AC power plug of the charger for 1 miniute, and
then insert the AC power plug and the battery again. If
the indictor shows charging, that means the battery is
good. If not, the battery needs to be changed.
CHECKING THE CHARGER
If the battery pack does not charge properly:
„ Check the current at the power outlet with another
tool. Make sure that the outlet is not turned off.
„ Check that the charger contacts have not been
shorted by debris or foreign material.
„ If the surrounding air temperature is not normal room
temperature, move the charger and battery pack to a
location where the temperature is between 7 ˚C and
40˚C .
„ This product requires assembly.
If the battery is inserted into the charger when warm
or hot, the CHARGING LED indicator light on the
charger may switch on and illuminate ORANGE. If
this occurs allow the battery to cool outside of the
charger from approximately 30 minutes.
CHARGER MOUNTING
1.This charger can be installed hanging on a wall using
two screws (not supplied).
2.Locate the placement for the charger to be wall
WARNING

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Bt 48 li 4.0Bt 48 li 2.5Bt 48 li 5.0

Table des Matières