Additional Specific Safety Rules; Power Connections; Motor Specifications; Grounding Instructions - Delta AP-100 Manuel D'utilisation

ADDITIONAL SPECIFIC SAFETY RULES

DO NOT USE THIS UNIT TO FILTER METAL
DUST. Combining wood and metal dust can create an explosion
or fire hazard. This unit is intended to filter non-explosive
atmospheres only.
DO NOT USE THIS UNIT TO DISSIPATE FUMES
OR SMOKE. Explosions or fire can result. This air cleaner is
intended for use where only dry airborne dust is present. Its use
should be limited to non-explosive, non-metallic atmospheres.
1. DO NOT OPERATE THIS UNIT until it is completely
assembled and installed according to the instructions. A unit
incorrectly assembled can cause injury.
2. OBTAIN ADVICE from your supervisor, instructor, or
another qualified person if you are not thoroughly familiar
with the operation of this unit. Knowledge is safety.
3. FOLLOW ALL WIRING CODES and recommended electrical
connections to prevent electrical shock or electrocution.
4. DO NOT LIFT THIS UNIT BY THE POWER CORD. Do
not use the power cord as a hanging device. A damaged
power cord can cause electrical shock or electrocution.
5. SECURELY ANCHOR THIS UNIT to a permanent or fixed
supporting structure when suspending it from the ceiling.
A falling unit can cause serious injury. Always keep a
minimum of 7 feet between the bottom of the unit and the
floor surface to allow for sufficient head clearance. Use
only a chain rated for a minimum of 150 lb. working load
to adequately hold the unit. Use steel S-Hooks that are at
least 1/4" in diameter to suspend the unit from the ceiling.
Lag-type bolts used to suspend the unit from the ceiling
must be threaded at least 1-1/2" into supporting structural
members.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected
with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs
and matching receptacle which will accept the machine's plug. Before connecting the machine to the power line, make sure the switch
(s) is in the "OFF" position and be sure that the electric current is of the same characteristics as indicated on the machine. All line
connections should make good contact. Running on low voltage will damage the machine.
Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source, make sure the
switch is in the "OFF" position.

GROUNDING INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.
Failure to follow these rules may result in serious personal injury.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
6. SUPPORT THIS UNIT or securely clamp it to the work
surface when it is used in a portable application to
eliminate potential injury and/or damage to the unit.
7. ENSURE THAT THE INTAKE AND EXHAUST AREAS
ARE CLEAR prior to starting the unit. Clogged intakes or
exhausts can cause an explosion and/or fire.
8. KEEP ARMS, HANDS, AND FINGERS AWAY FROM
THE FAN. Avoid all exposure to rotating parts to prevent
injury.
9. DO NOT OPERATE THIS UNIT WITHOUT THE FILTERS
IN PLACE. Dust and other small debris will go directly to
the motor, causing over-heating and the potential for fire
and/or explosion.
10. DO NOT ATTEMPT to remove or replace the filter(s) while the
unit is running. Exposed fan blades can cause severe cuts.
Make certain that the unit is disconnected from the power
source.
11. MAINTAIN THE UNIT in top condition. Clogged filters
can increase the potential for fire or explosion. Follow all
instructions for changing and cleaning filters.
12. STORE THE UNIT in a location that eliminates the
potential for damage to the power cord. A damaged
power cord can cause shock or electrocution. Safely store
power cord on the unit to eliminate tripping hazards.
13. TURN THE UNIT "OFF" and disconnect the unit from the
power source before installing or removing accessories,
before adjusting or changing set-ups, or when making
repairs. An accidental start-up can cause serious injury.
5