Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
French Fry Blade Assembly
CAUTION: Make sure that the unit is
unplugged from the power source and
the speed control dial is in the "OFF"
position before inserting or removing
attachments.
Note: The French Fry Blade is already
assembled to the blade holder. Do not
try to remove it. (Fig. 13)
1. Fit the processor bowl and spindle
as detailed previously.
2. Using the finger holes in the french fry
blade holder, fit it over the spindle and
press firmly into place as indicated.
(Fig. 14)
WARNING: USE EXTREME
CAUTION WHEN HANDLING
BLADES. BLADES ARE SHARP.
4. Fit the lid and click into place as
indicated in Setting Up section
(page 4).
5. Plug in the processor.
6. WARNING: USE THE FOOD
PUSHER TO ADD FOOD INTO THE
PROCESSOR BOWL THROUGH
THE FEEDER TUBE.
Do not overload the bowl. In one
operation, you can process a
maximum 6 cups (1500 ml) of food.
Fig. 14
Fig. 13
Processing Examples
THIN SLICING
THICK SLICING
For thin slicing:
-
Recommended speed level is High
(Cucumbers, raw potatoes, lettuce, carrots)
For coarse slicing:
-
Recommended speed level is High
(Cabbage, carrots, onions)
For fine shredding:
-
Recommended speed level is High
(Carrots, cucumbers, cabbage)
For coarse shredding: -
Recommended speed level is High
(Lettuce, carrots, apples)
Blade & Accessory Storage
When storing your appliance, place the
blades in the blade storage area on top of
the unit under the cover. The spindle and
the dough blade can be stored in the front
storage compartment. The double
chopping blade is left in the food
processor bowl. The french fry blade
must be stored carefully out of the reach
of children in a cupboard along with the
blade holder for the other blades. Use
caution when handling the blades as they
are sharp. See figure 15 for suggested
storage placement.
Fig. 15
FINE SHREDDING
COARSE SHREDDING
7
CLEANING & MAINTENANCE
CAUTION:
Make sure that the unit is unplugged from power source and speed
control dial is in the "OFF" position before inserting or removing any
attachments and before cleaning.
•
Never immerse the unit, cord or plug
in water or any other liquid.
•
Clean the main unit with a damp
cloth only.
•
Only the stainless steel blades can
be washed in the dishwasher.
•
All other parts can be cleaned in
warm sudsy water using regular
dishwashing liquid.
•
If food has spilled over on to the
main unit, use the pointy end of the
spatula to clean the cracks and
crevices of the base under the food
processor bowl. (Fig. 16)
Fig. 16
Hints & Tips:
•
The double chopping blade can be
used for chopping meat, fish,
vegetables, cheese, etc. setting
the speed to maximum.
•
For finer chopping, increase the
length of time you process.
•
For coarser chopping, use the pulse
button for a few seconds and monitor
food texture.
•
Pre-cut larger pieces to make them fit
into the feed tube. When chopping
hard foods (e.g. meat, cheese) cut
into 1 "/2.4 cm cubes.
•
For shredding, place food horizontally
into the feed tube, for slicing place the
food vertically.
Re-settable Thermal Safety
Device
Your Food Processor has been
designed with a unique safety system
which prevents damage to the unit's
motor and drive system, should you
inadvertently overload your appliance.
The safety system will automatically cut
the electric power to the appliance
when the device senses an overload or
excessive temperature in the motor or
drive system. Should this occur during
use and the appliance stops
functioning, follow the re-setting
procedure below:
1.
Turn the "ON/OFF" speed control
to the "OFF" position
2.
Unplug the unit from the wall
receptacle.
3.
Remove and empty the processor
bowl. Ensure that no food is
jamming the cutting blades or
attachments.
4.
Allow the appliance to cool down
for a minimum of 30 minutes.
5.
Re-install the processor bowl and
re-plug appliance in the wall outlet.
6.
Proceed to use the appliance as
before. Should the appliance still
fail to operate, turn the "ON/OFF"
speed control to the "OFF" position
and unplug from the wall outlet.
Allow the appliance to cool down
for an additional 1 to 2 hours. After
this time has passed, repeat the
restart procedure, steps 5 and 6
above.
8
Publicité
Table des Matières
