Power Supply - Monacor security AV-3080COL Mode D'emploi

4.4 Power supply

For power supply, a regulated 12 V power supply unit
with a minimum constant output current of 300 mA is
required, e. g. MONACOR PS-500ST. As the camera
will only have a very low current consumption (max.
1.5 mA) in stand-by mode, a power supply independ-
ent of the mains supply is also possible via a 12 V
rechargeable battery.
1) In case of a power supply unit with variable output
voltage, adjust the voltage to 12 V.
2) Connect the power supply via a low-voltage plug
5.5/2.5 mm (outside/inside diameter) to the inline
jack (9). Always observe the correct polarity: The
positive pole must be at the inner contact of the
plug.
3) After applying the operating voltage, the camera is
ready for operation.
4.5 Noise and motion detectors
1) Use the DIP switches (6) on the side of the unit
according to fig. 3 for defining which detectors will
activate the camera or for setting the camera to
continuous operation.
2) With at least one of the detectors activated, adjust
the tracking time with the control (7) between
approx. 2 seconds (left stop) and 5 minutes (right
stop). The tracking time is the time for which the
camera will remain activated after the last move-
ment or noise detected.
3) If the noise detector (3) is activated, adjust the
sensitivity with the control (1):
Control turned counter-clockwise to the left stop =
high sensitivity, i. e. already a low noise will
activate the camera.
Control turned clockwise to the right stop = low
sensitivity, i. e. only a loud noise will activate the
camera.
4.6 Focus setting
Turn the lens (8) to adjust a clear picture on the moni-
tor.
4.7 Control channel
As long as the camera is activated, it will emit a con-
trol signal via a control channel. If the receiver is also
provided with a control channel, it is possible to
activate an acoustic or visual signal device or another
additional unit (e. g. a video recorder for automatic
start of a recording) via this channel.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
5 Specifications
Approval No.: . . . . . . . . . .
Transmission frequency: . channel 1
Transmitting power: . . . . . ≤ 25 mW (EIRP)
Antenna: . . . . . . . . . . . . . omnidirectional antenna
Operating range
Video
Audio
Modulation audio/video: . frequency-modulated
Lens: . . . . . . . . . . . . . . . . 1 : 2.0/3.8 mm (72°)
Minimum illumination: . . . 5 lux
Resolution: . . . . . . . . . . . . 330 lines
Detection range
of motion detector: . . . . . . 5 m, hor. 100°, vert. 82°
Operating voltage: . . . . . . 12 V
Current consumption: . . . 290 mA
Ambient temperature: . . . 0 – 40 °C
Dimensions w/o antenna: 55 x 55 x 45 mm
Weight: . . . . . . . . . . . . . . . 95 g
Subject to technical modification.
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
®
without any obstacles:
in buildings: . . . . . . . . . 50 m max.
Signal format: . . . . . . . CCIR
Colour system: . . . . . . . PAL
Bandwidth: . . . . . . . . . . 30 Hz – 5 MHz
Bandwidth: . . . . . . . . . . 15 Hz – 15 kHz
Audio transmission: . . . mono
Quiescent current
(only detectors ON) . . . max. 1.5 mA
0682
!
2.4145 GHz
channel 2 2.4285 GHz
channel 3 2.4425 GHz
channel 4 2.4565 GHz
channel 5 2.4705 GHz
500 m max.
625 lines
50 fields/s
F3F
±0.5 V
9