Explanation Of Functions - Vivanco FMH 7190 Mode D'emploi

FMH 7190
Congratulations on purchasing your new Vivanco product. This wireless headphone
system operates using the latest transmission technology. Enjoy your favourite music or
films in top quality stereo sound without inconvenient cable connections. With the SRS
TruSurround XT® System you can also convert any normal stereo sound into breathtaking
virtual surround sound.
A Transmitter
1 Charging indicator light
2 Operation indicator light
3 SRS TruSurround XT®* indicator light
4 SRS TruSurround XT®* switch
5 Channel selection switch
6 Audio connecting cable
7 AC adaptor connector
8 AC adaptor
9 RCA adaptor
10 Jack adaptor 3.5 mm to 6.35 mm
B RF headphone
1 Charging contacts
2 Earshell with battery compartment
3 On/off switch (OFF/ON)
4 Volume control (VOL)
5 Operation indicator light
6 Channel selection button (TUNE)
7 Balance control left/right (L/R)
Important information
Please read these operating instructions carefully and keep them in a safe place.
Do not use the devices in water or rain.
The AC adaptors are designed for these devices only. Do not use the supplied AC
adaptors with other devices.
Avoid exposure to extreme heat or strong light.
Do not open the housings or the AC adaptors (danger of electric shock!).
Check whether the local mains voltage corresponds to the voltage indicated on the
AC adaptor.
Avoid touching the battery or charging contacts. Do not touch the contacts with
metal objects.
Do not cover the devices (e.g. with a towel, sheet, etc.)
Clean the devices using a moist cloth and never use aggressive cleaning agents.
Constant use at high volumes impairs your hearing and may cause permanent
damage.
Do not dispose of this product with the domestic waste; take it to your local
electronic waste recycling depot.
Preparing your RF headphone
1. Place the transmitter near to your hi-fi system, your TV or another audio source.
2. Connect the AC adaptor to the connector on the transmitter, then plug it into a mains
socket.
8
GB GB
3. Connect the audio connecting cable to a headphone output, or to a line out or rec.
out output. Set the volume of your audio source to 1/4 to 1/3 of the maximum
volume.
4. If the charge indicator doesn't change to red, move the handset back and forth slightly
in the charging shell until the charging contacts snap into place correctly and the
charge indicator changes to red.
5. Insert the supplied batteries as described in the chapter "Using batteries or
rechargeable batteries".
6. Switch on the RF headphone via the on/off switch.
7. Press the channel selection button on the RF headphone in order to automatically
locate the transmitter. If the transmitter has been located, the operating indicator
lights up green.
8. Your device is now ready for operation.

Explanation of functions

SRS TruSurround XT®*
The SRS TruSurround XT ®* technology allows you to play a surround sound audio source
(for example DVD) on a stereo headset in comparable quality. You can turn this virtual
surround sound on or off depending on your need, by simply pressing the SRS
TruSurround XT®* switch. If the effect is switched on, the display is blue. You achieve
the ideal surround effect if your audio source plays the audio data in Dolby Pro Logic or
Pro Logic II quality.
Auto-Tuning
If interference is received, select a different channel on the transmitter (channel select
switch). Then press the channel select button on the RF headphone and the new
transmitter is located automatically.
Balance
You can adjust the loudness ratio between the left and right channels. Turn the balance
control in the respective direction. The middle position produces a balanced sound image
between the left and right sides of the music signal.
Standby mode
The transmitter switches automatically to standby mode if it does not receive any signal
for 2 minutes or if the signal is too quiet. It switches automatically back to transmission
mode as soon as a signal is present again.
Using batteries or rechargeable batteries
Opening the battery compartment
1. To open the battery compartment, carefully pull off the ear cushion from the left side
earshell "L". The battery compartment is located behind this.
2. Insert the batteries or rechargeable batteries (micro, type AAA) into the battery
compartment, observing the correct polarity.
3. Place the ear cushion over the battery compartment again and press it carefully until
it latches.
9