Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
Run Time
When fully charged, the average effective usage times are
between 10-15 minutes.
It may take several chargings before these times can
be achieved.
MAINTENANCE
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Cleaning
WARNING:
out of all air vents with clean, dry air at least once
a week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Dust Bowl (Fig. D)
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying
Refer to Filter to remove the dust bowl
•
•
The dust bowl can be washed in warm soapy water.
Ensure that it is dry before re-attaching.
Motor Section (Fig. D)
iMPORTAnT: Never immerse the product in water.
A damp cloth and soapy water should be used to clean the
exterior of the motor section
is completely dry before re-use or storing.
Filter (Fig. D)
nOTE: The product performs better with a clean filter and
pre-filter.
•
Remove the pre-filter
9
dust off the filter.
•
Empty the dust from the dust bowl
if necessary.
•
Wash the pre-filter regularly using warm, soapy water.
Ensure that it is completely dry before using again.
8
To reduce the risk of serious
Blow dirt and dust
Never use solvents or other
3
.
10
. Always ensure the product
and shake or lightly brush loose
3
and wash
Accessories
WARNING:
those offered by CRAFTSMAN, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1‑888‑331‑4569 .
On Board Storage (Fig. A)
The crevice
7
slides into the on board storage
the motor housing.
VersaTrack™ (Fig. H)
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
WARNING:
personal injury, do not use a damaged VersaTrack™
hang hook or VersaTrack™ Trackwall. A damaged
VersaTrack™ hang hook or VersaTrack™ Trackwall will
not support the weight of the tool.
WARNING:
personal injury, ensure the screw holding the
VersaTrack™ hang hook is securely tightened.
WARNING:
personal injury, DO NOT suspend tool overhead or
suspend objects from the hang hook. ONLY suspend
tool on the VersaTrack™ Trackwall using the hang hook.
WARNING:
does not exceed the maximum rated weight of 20 lb (9
kg) for the selected VersaTrack™ hook.
WARNING:
VersaTrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linear foot.
iMPORTAnT: When attaching the VersaTrack™ hang hook,
use only the screw that is provided. Be sure to securely
tighten the screw. VersaTrack™ accessories mount compatible
tools securely to the VersaTrack™ Trackwall system.
1. Turn the tool off, remove the battery pack
and accessories.
Since accessories, other than
8
underneath
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
To reduce the risk of serious
Ensure that the tool weight
When hanging objects on a
Publicité
Table des Matières
