Table des Matières
Publicité
Electrical safety
• Power tool plugs must match the outlet. Do not modify
the plug in any way. Do not use any adapter plugs
with grounded devices. Unmodified plugs and match-
ing outlets will reduce the risk of electric shock.
• Avoid physical contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators. If your
body is grounded the risk of an electric shock in-
creases.
• Do not expose the power tool to rain or wet condi-
tions. Water that enters a power tool will increase the
risk of electric shock.
• Do not abuse the cord; do not use the cord to carry
or hang up the power tool or to unplug the power tool
from the mains. Keep the power cord away from heat,
oil, sharp edges or the power tool's moving parts.
Damaged or tangled power cords will increase the
risk of electric shock.
• When operating a power tool outdoors, use only ex-
tension cords that are approved for outdoor use. The
use of an extension cord that is adapted for outdoor
use reduces the risk of electric shock.
• If working with the power tool in a damp location can-
not be avoided, use a ground fault circuit interrupter.
The use of a ground fault circuit interrupter reduces
the risk of electric shock. Always check whether the
mains voltage complies with the voltage specified on
the nameplate of the power tool.
Personal safety
• Stay alert. Watch what you are doing and use com-
mon sense when operating a power tool. Do not use
the power tool while you are tired or under the influ-
ence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
• Use personal protective equipment. Always wear
safety glasses. Safety equipment such as a dust
mask, non-skid safety shoes, a hard hat or ear pro-
tection depending on the type and use of the power
tool will reduce personal injuries.
• Prevent unintentional starting. Ensure that the power
tool is switched off before connecting it to the power
supply and/or battery, picking it up or carrying the
tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch
on invite accidents.
• Remove any adjusting tool or wrench before turning
the power tool on. A wrench or a key which has been
left attached to a rotating part may induce personal
injury. Do not overreach. Keep proper footing and bal-
ance at all times. This enables you to better control
the power tool in situations which cannot be foreseen.
• Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair
may get caught in moving parts.
• If dust extraction and collection units are installed,
make sure that these are connected and properly
used. Using such devices reduces hazards associ-
ated with dust.
12 І 128
Heruntergeladen von
manualslib.de
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
Handbücher-Suchmachiene
Power tool use and care
• Do not force the power tool. Use the correct power
tool for your application. With the correct power tool
you will do the job better and safer at the specified
power rate.
• Do not use the power tool if it has a defective switch.
A power tool, which cannot be turned on or off with
the switch, is dangerous and must be repaired.
• Unplug the power cord from the outlet and/or remove
the battery before making any adjustments to the tool,
changing accessories, or storing the power tool. Such
preventive safety measures prevent starting the tool
accidentally.
• Store idle power tools out of children's reach. Do not
allow persons unfamiliar with the tool or these instruc-
tions to operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
• Keep the power tools in good condition. Check that
moving parts are functioning smoothly and do not
lock, whether parts are broken or for any other con-
dition that may affect the power tool's operation. If
damaged, have the power tool repaired before use.
Many accidents are associated with poorly main-
tained power tools.
• Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are likely
to block less and are easier to control.
• Use the power tool, the accessories, bits, etc. in ac-
cordance with these instructions and in the manner
intended for the particular type of equipment. Take in-
to account the working conditions and the work to be
performed. Using power tools for operations different
from those intended can lead to hazardous situations.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the electric tool.
Maintenance and Service
• Have your power tool serviced by a qualified repair
workshop using only original replacement parts. This
will ensure that after repairs the safety of the power
tool is maintained.
• Damaged cords must be replaced by our after-sales
service.
• If a power plug is damaged, it must be replaced by
a special spare plug provided by our after-sales ser-
vice. If the supply cord of the tools is damaged, it
must be replaced by a special cord, which is available
from the manufacturer or its after-sales service. The
replacement of the connecting cord must be carried
out by our after-sales service or by a qualified repair
workshop.
Publicité
Table des Matières
