Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
PLAYING MP3s FROM A DEVICE
1.
Connect a USB device or SD card with MP3 files to the USB SLOT or SD CARD SLOT respectively. The LCD
will show "USB READ" or "CARD READ" when it is properly connected, and "USB" or "CARD" will be shown in
the upper right corner.
2.
The LCD will display the total number of folders on the device (on
the left) and the total number of available tracks (on the right).
Use the SKIP
can also press the NEXT FOLDER button to jump to the first track
of the next folder. The current track will begin playing.
3.
The LCD will show the "PLAY" icon, the track number, and the
time elapsed.
• To skip to another track, use the the SKIP
The LCD will briefly show the number of the folder and new
track. (Note:
play the first track of the next folder.)
• To pause playback, press the PLAY / PAUSE button. Press it again to resume playback.
• To stop playback, press the STOP ( ) button.
• To change how PROFILE FLASH plays the tracks, press
the PLAY MODE button:
Repeat: The current track will repeat.
a.
Repeat All: The entire collection of tracks on your
b.
connected device will repeat.
Repeat Folder: The collection of tracks in the
c.
current folder will repeat.
Random: The entire collection of tracks on your connected device will play in random order.
d.
4.
To eject the device, first stop the current track by pressing the STOP ( ) button. If your device is a USB drive,
gently pull it from the slot. If your device is an SD card, push it into the slot until it clicks, then gently remove it.
RECORDING MP3s TO A DEVICE
1.
Connect a USB device or SD card to the USB SLOT or SD CARD SLOT respectively. The LCD will show "USB
READ" or "CARD READ" when it is properly connected, and "USB" or "CARD" will be shown in the upper right
corner.
2.
If the device already contains MP3s, the LCD will display the total
number of folders on the device (on the left) and the total number
of available tracks (on the right).
3.
Cue up the music you want to record from a record on the
PLATTER or a device connected to the AUDIO INPUT.*
4.
Press REC. The LCD will display "LOADING." When the "PLAY /
PAUSE" icon and time display are flashing on the LCD, PROFILE
FLASH is ready to record.
5.
To begin recording, press PLAY / PAUSE. Items on the LCD will
flash briefly and "REC" will be shown to indicate PROFILE
FLASH is recording. The LCD will show the track number and
the time elapsed.
• To start a new track immediately without stopping the
recording process, press SPLIT TRACK.
recording track will stop and a new recording will begin.
(Tracks that are split will be given sequential track numbers
and stored in the same folder.)
• To stop recording, press the STOP ( ) button. (The LCD
will show "USB READ" or "CARD READ" to show it is
rescanning the connected device for your new tracks.)
6.
After stopping the recording, you may play your new tracks or
eject your device. To eject the device, first stop the current track
by pressing the STOP ( ) button. If your device is a USB drive,
gently pull it from the slot. If your device is an SD card, push it
into the slot until it clicks, then gently remove it.
/
buttons to move through the tracks. You
Pressing NEXT FOLDER will immediately
/
buttons.
The currently
* Note: If you are recording from a
device connected to the AUDIO
INPUT
recommend monitoring the volume
meter on the upper right corner of the
LCD while recording and adjusting
your device's volume accordingly.
Make sure the level is high enough to
be heard but not high enough to
produce
(indicated by an "X" on the meter).
3
on
the
rear
panel,
"clipping"
or
distortion
we
Publicité
Table des Matières
