Detergent Dispenser - Hoonved C 43 E Série Mode D'emploi Et Entretien

ENGLISH
3.2 SETTING CYCLES for
REGENERATION PROMPT
(models C D-SP D only)
ATTENTION
Before setting the cycles for the resin regeneration
prompt, SWITCH OFF the dishwasher by pressing the
power switch (Q1) into the OFF position, and SWITCH
the mains power supply to the " O " OFF position.
It is now possible to carry out the cycle settings for the
regeneration-phase prompt.
IMPORTANT
We recommend that setting the regeneration cycle
prompt should be the first operation you carry out.
With the machine SWITCHED OFF and the door OPEN,
set the dip switches as shown in the following table:
no cycle count
1
ON
1 2 3 4
ON
OFF
OFF
45 cycles
ON
1 2 3 4 ON 1
OFF
OFF
50 cycles 80 cycles
ON
1 4 1
2 3
ON
OFF
OFF
55 cycles
ON
ON
1 4 1
2 3
OFF
OFF
60 cycles
ON
1 2 3 4 ON
1
OFF
OFF
65 cycles
ON 1 4 ON 1
2 3
OFF OFF
Having set the dip switches, switch the machine back
on at the mains " 1 " ON.
Power-up the machine using the power switch (Q1), at
the same time pressing and holding the
(S3).Wait for a few seconds then release the
(S3) button.
The confirmation of the occured programming can be
attained in the following way: close the machine door.
The machine should not fill up the tank.
After that, switch off the machine with the Line (Q1)but-
ton and wait for a few seconds. When switching on the
machine again, it should function regularly."
30
70 cycles 100 cycles
2 3 4 ON 1 2 3 4
OFF
75 cycles
105 cycles
ON 1 2 3 4
2 3 4
OFF
110 cycles
2 3 4 ON 1 2 3 4
OFF
85 cycles 115 cycles
ON
2 3 4 1 2 3 4
OFF
90 cycles
2 3 4
95 cycles
4
2 3
START
button
START
Part 3: For the technician
3.3

DETERGENT DISPENSER

(Optional) (Fig. 8)
The machine is equipped with an automatic detergent
dispenser.
• Insert the red supply tube (16) into the canister (17).
ATTENTION
Always wash the hands under running water if they come
into contact with detergent, or comply with the specific
indications pertaining to the utilized type of detergent itself.
• Proceed with a few no-load cycles until the intake and
delivery tubes have filled.
To adjust the dispenser, refer to the relative enclosed ma-
nual and to the utilized type of detergent.
3.4 FILLING THE RINSING AGENT
DISPENSER (Fig. 8)
• Insert the transparent tube (18) into the canister (19)
containing rinsing agent.
• Start the machine as described in paragraph 2.1. The
dispenser will suck about 3 cm of liquid from the canister.
• Fill during the cycle by opening (slightly) and closing
the door until the tube has completely filled.
3.4.a Adjusting the dose (Fig. 8)
• Start the machine as described in paragraph 2.1 and
hold a glass up to the light at the end of the cycle.
• The drops of water on the glass will indicate insufficient
dosage while streaks will indicate that dosage is exces-
sive either in relation to density or quantity.
• Regulate by means of the plug (20), turning clockwise
to decrease the quantity or anticlockwise to increase it.
IMPORTANT
These data are indicative and not binding since they may
vary according to the hardness of the water or the utilized
type of detergent and rinsing agent.
ATTENTION
If the utilized product (detergent or rinsing agent) is changed,
it is advisable to flush out the dosing system with water and
to then proceed by filling the dispensers.