Technical Data - Tecomec Easy Rivet Manuel D'utilisation Et Entretien

5. DEFINITIONS
Skilled technician: a person who is generally employed by the
service centre and who is trained to carry out extraordinary
maintenance jobs and repairs on the machine.
6. SyMBOLS
This symbol points out the possibility of serious
personal injuries if the provisions and instructions
are not observed.
This symbol points out that the user must wear
protection goggles when using the machine.
This symbol points out that the user must wear
protective gloves when using the machine.

7. TECHNICAL DATA

Model
Voltage
Rated power
Max.speed of insert
Acoustic pressure level
Level of vibrations on
operating handle
Types of chains on
which rivets can be
spun
Weight (complete
machine)
8. PART DESCRIPTION (FIG.1)
1 base unit
2 motor unit
3 operating wheel
4 spinner tool
5 insert tip
6 chain guide disc
9. SAFETy DEVICES
The rivet spinner is equipped with the safety devices
illustrated hereafter:
- Switch: the machine features a safety switch with release
coil. In the case of a sudden power failure, the switch
trips automatically and disconnects the machine from the
mains. The machine will not start even if the power supply
is suddenly restored. You need to reset the switch to start
the machine again.
10. INTENDED USE
This device is an electric rivet spinner for cutting chains
used in chain saws.
- Use the machine exclusively for the types of chains stated
in the technical data chart.
- Do not use the rivet spinner for anything other than the
stated chains.
6
Tecomec - Easy Rivet
PrecisionTooling - River Spinner Auto
230V~ 50Hz 120V~ 60Hz
85W 85W
-1
160 min 160 min
< 85 dB(A)
2
< 2,5 m/s
1/4" - .325" - 3/8" - .404"
7,5 kg
7 spinner tool
8 insert tip
9 main ON/OFF switch
10 electrical power cable
11 rating nameplate
12 thrust bearing
EN
- Secure the device firmly to the bench.
- The machine must not be used in corrosive or explosive
environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following
improper or incorrect use of the machine.
11. UNPACKING
The rivet spinner is supplied partially assembled.
12. STANDARD SUPPLy (FIG.2)
1 - Rivet spinner
2 - owner's manual
3 - test card
4 - chain guide disc unit
securing screws of the
5 -
chain guide disc
spinner tool (type A) for
6 -
chains: 3/8"-.404"
-1
13. INSTALLATION
ATTENTION
Do not install the machine at eye level. You are recommended
to install it on the bench at a maximum height of approximately
1.2-1.3 m off the floor.
13.1 MOUNTING (FIG.3)
- To secure the base, use two M8 screws complete with nuts
and washers (material not supplied) inserted in the slots
A1. Make sure you position the rivet spinner on the work
bench as illustrated.
13.2 MOUNTING THE CHAIN GUIDE DISCS (FIG.4)
- To secure the two chain guide discs G2, screw the four
V4 screws into the four holes F1 (using the provided allen
key).
13.3 MOUNTING THE HANDLE WHEEL (FIG.4A)
- Fit V6 screw into the M1 handle hole.
- Screw the V6 onto the V5 wheel using proper allen key
(not provided).
14. CHAIN INFORMATION
The chain must be completely inspected before spinning its
rivets to make sure it is intact.
Chain parts (fig.5) :
1 connection link
1a connection link with rivets
2 left cutter
3 right cutter
4 driving link (pulling link)
spinner tool (type B) for
7 -
chains: 1/4"-.325"
insert tip (type A) for
8 -
chains: 3/8"-.404"
insert tip (type B) for
9 -
chains: 1/4"-.325"
10 operating wheel
11 wheel handle
12 handle srew