Table des Matières
Publicité
•
Have damaged switches replaced by a customer ser-
vice workshop.
•
This electric tool complies with the pertinent safety
regulations. Repairs are to be carried out only by a
qualified electrician using original replacement parts
or the user may suffer an accident.
•
If necessary, wear suitable personal protection equip-
ment. This could consist of:
- Ear-muffs to prevent the risk of damaging your hea-
ring
- A breathing mask to prevent the risk of inhaling ha-
zardous dust
•
The operator has to be informed about the conditions
with an influence on noise development.
•
Faults on the machine have to be reported to the per-
son in charge as soon as they are discovered.
•
This appliance is not suitable for the collection of dan-
gerous dust.
•
This equipment is not designed to be used by people
(including children) with limited physical, sensory or
mental capacities or those with no experience and/
or knowledge unless they are supervised by a per-
son who is responsible for their safety or they have
received instructions from such a person in how to use
the equipment safely. Children must always be super-
vised in order to ensure that they do not play with the
equipment.
Technical Data
Motor
Motor speed
Power P
Protection type
Max. vacuum
Max. extraction volumes
Extractor socket
Sawdust bag volumes
Weight
Noise emission values
sound pressure level L
pA
sound power level L
WA
The quoted values are emission values and not ne-
cessarily reliable workplace values. Although there is
a correlation between emission and immission levels
it is impossible to draw any certain conclusions as to
the need for additional precautions. Factors with a po-
tential influence on the actual immission level at the
workplace include the duration of impact, the type of
room, and other sources of noise etc., e.g. the number
of machines and other neighboring operations. Reli-
able workplace values may also vary from country to
country. With this information the user should at least
be able to make a better assessment of the dangers
and risks involved.
Assembly
For packaging reasons your machine is delivered in
semi-assembled state.
• Attach the side covering loosely to the base frame us-
ing flat-head screws M8 x 40 mm and screw nuts. Do
not tighten completely. Fig. 2, 3
• Attach the cross-member to the side covering left and
• Remove all screws and nuts form the housing.
• Attach the housing to the side coverings using flat-
• Slide the clamp through the tabs on the filter bag and
• Position the support bar into the housing and hang the
• Attach the shavings bag to the lower air ventilator us-
• Attach the exhaust hose to the nozzle on the housing
• Attach the hose coupling to the other end of the hose
The exhaust system should be cleaned every time the
shavings bag is changed.
Damaged filters and bags must be immediately changed
in order to keep the amount of dust that escapes into the
work environment as low as possible.
Initial operation
Note safety instructions before operation. The data on the
motor type plate (voltage and frequency) must conform to
the mains supply voltage and frequency. After connection
to the mains, the Dust Extractor is ready for operation.
Maintenance
m Warning! Prior to any adjustment, maintenance or
230 V /50 Hz
service work disconnect the mains power plug!
2850 min
-1
General maintenance measures
550 W
• Keep all safety devices, air vents and the motor hous-
IP20
1600 Pa
1150 m
/h
3
• We recommend that you clean the equipment imme-
100 mm
• Clean the equipment regularly with a damp cloth and
75 l
20 kg
75.5 dB(A)
Storage
95.5 dB(A)
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with these
regulations.
• Given unfavorable conditions in the power supply the
• The product is exclusively intended for use at con-
• As the user, you are required to ensure, in consulta-
right with flat-head screws M 8 x 12 and screw nuts.
Fig. 4, 5
head screws M5 x 20 and screw nuts. Securely tighten
all nuts. Fig. 6
fix the filter bag on the container. Fig. 7
filter bag from it. Fig. 1
ing the clamp. Fig. 7
and affix it with a hose clamp. Fig. 8
using a hose clamp. Fig. 9
ing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it down with com-
pressed air at low pressure.
diately after you use it.
some soft soap. Do not use cleaning agents or sol-
vents; these may be aggressive to the plastic parts in
the equipment. Ensure that no water can get into the
interior of the equipment.
product can cause the voltage to fluctuate temporarily.
nection points that have a continuous current-carry-
ing capacity of at least 100 Amper phase.
tion with your electric power company if necessary,
that the connection point at which you wish to ope-
rate the product meets the specified requirements.
13 І 100
Publicité
Table des Matières
