Manuels Connexes pour DOSMATIC MiniDos 1%
Sommaire des Matières pour DOSMATIC MiniDos 1%
- Page 1 MiniDos Installation & Operating Instructions Manuel d’Installation et d’Utilisation Instrucciones para Instalacion y Operacion Model No. 1.0 % 2.5 % 5.0 % 10.0 % ISO 9001:2000 Quality Management System...
-
Page 2: Table Des Matières
CONTENTS CAUTION: To reduce risk of injury, user must read and understand the Installation & Operating In- structions before using this product ITEM PAGE Introduction…………….… 3 Safety…………………..4 Installation…………..5-7 Operation……………..8-9 Maintenance…………. 9-10 Trouble Shooting…..10-11 Specifications………..…. 12 Repair Parts Motor….…. 13 Repair Parts Lower…... -
Page 3: Introduction
(as shown in figure El inyector se entrega con los si- lescomposants suivants (comme guientes componentes (como se représentésur le schéma 1): representa en el Dosmatic injector (not shown) esquema 1): L’injecteur DOSMATIC (non Dosage piston (A) représenté) O-ring (B) -
Page 4: Safety
SAFETY 1. SELECT A LOCATION: That LUGAR ENDROIT Elija un lugar que responda a todas las is on the water line that chemi- Choisissez un endroit qui répond à condiciones siguientes así como a las cal injection is desired and toutes les conditions suivantes ainsi normativas locales: meets all the following require-... -
Page 5: Installation
INSTALLATION INSTALLATION INSTALACIÓN SEE FIG 2 Voir Fig 2 1 NOTA : el agua que abastece la 1 NOTE : L’eau qui passe par l’in- instalación no debe contener are- 1. NOTE: Water going through in- jecteur ne doit pas contenir de sa- na fina u otros abrasivos. -
Page 6: Typical Installation
INSTALLATION DWG. TYPICAL INSTALLATION * Consult local code requirements for backflor prevention. Fig. 2 Fig. 3... -
Page 7: Operation
OPERATION ACTION DU DEBIT : Le débit ACCIÓN DEL CAUDAL: El cau- SERVICE FLOW: Water drawn d’eau motrice vers le doseur en- dal de agua motriz hacia la bomba down stream from the injector will traînera automatiquement le fonc- implica automáticamente el funcio- automatically cause the injector to tionnement de l’appareil qui namiento del la bomba que hace... -
Page 8: Maintenance
OPERATION Cont. Caution: Injector is under line water pressure regardless of the position of the “Bypass Lever”. Bypass Lever Setting Indicator Mark Run Position Fig 5 MAINTANANCE RINCER LA POMPE APRES ACLARAR CON AGUA LA BOMBA RINSE INJECTOR AFTER DESPUÉS DE CADA USO: Si queda CHAQUE USAGE: La solution qui solución en el interior de la bomba, ésta EACH USE:... -
Page 9: Trouble Shooting
MAINTANANCE Cont. STORAGE: For extended storage, NETTOYER LE RESERVOIR LIMPIE EL DEPÓSITO DE SO- rinse injector as described above DE SOLUTION : Le maintenir LUCIÓN: Manténgalo cerrado pa- and place entire injector underwater fermé pour éviter que des impure- ra evitar que las impurezas, insec- (in 5 gal container). - Page 10 TROUBLE SHOOTING 5. La surface interne du demi corps NO CLICKING SOUND . Si la superficie interna del me- supérieur #1 ou du demi corps infé- dio cuerpo superior #1 o del me- 5. Cover #1 or Main Body #40 dio cuerpo inferior #40 está...
-
Page 11: Specifications
0,11 lpm 45 lpm 1;100 1:10 0,41 – 6,9 bar ¾” bsp These are part numbers for standard units only, please request remote option when ordering. NOTE: Dosmatic reserves the right to change specifications without notice. Check with factory for lat- est specifications. -
Page 12: Repair Parts
REPAIR PARTS DRIVE MOTOR PARTS Reference Part # Description of Part 195100 Upper Body 212745V O-ring,cover/body 195710 On/Off Male 195711 On/Off Female 195700 Shaft 212009V O-ring, A10 195720 Mixing Chamber Gasket 011662M Piston Assembly * part #’s subject to change. - Page 13 LOWER END INJECTOR PARTS MiniDos 1.0 % * part #’s subject to change.
- Page 14 LOWER END INJECTOR PARTS MiniDos 2.5 % * part #’s subject to change.
- Page 15 LOWER END INJECTOR PARTS MiniDos 5 % * part #’s subject to change.
- Page 16 LOWER END INJECTOR PARTS MiniDos 10 % * part #’s subject to change.
- Page 17 Wear Parts Kits Manual Refer- Model: 2.5% Part # Description of Kits ence 011720V 17, 44 Kit A – Wear Parts Kits (dosage piston and o-ring) 011723V 14, 17, 44, 51 Kit B – Wear Parts Kit (Kit A, lower shaft and o-ring) Kit C –...
- Page 18 Wear Parts Kits Model: 5% Description of Kit Part # Manual Reference 011719V 17, 44 Kit A – Wear Parts Kit (dosage piston and o-ring) 011633 14, 17, 44, 52 Kit B – Wear Parts Kit (Kit A and shaft) Kit C –...
-
Page 19: Warranty
2. Return the unit to the distributor or to Dosmatic’s manufacturing facility, freight prepaid. Upon in- spection, the unit will be repaired or replaced, at Dosmatic’s option, free of charge, if found to be de- fective in material or workmanship and will be returned freight prepaid. -
Page 20: Locations
2. Remita el dosificador a su distribuidor, transporte pagado. Después de la inspección del mismo, será repara- do o reemplazado de forma gratuita. Se enviará de nuevo al usuario sin coste de transporte una vez Dosmatic haya comprobado el fallo en los materiales o en el proceso de fabricación.