Publicité
INSTRUCTIONS FOR USE
SAFETY INSTRUCTIONS
1. Please keep this instruction sheet safely for future reference.
2. Please do not modify the product or the assembly details in any way. Modifi cations will aff ect the structural
integrity and replacement parts will be at the buyer's expense. Inappropriate use or faulty application of the
product are explicitly forbidden and absolve the manufacturer of all liability. This product needs to be mounted
by an adult before use. For further assembly instructions see last pages.
3. The use of the item is only allowed under continuous supervision by an adult. This product is suitable for in-
dividuals weighing up to 100 kg. With exception of Bronco 0.6m, the Bronco slides are not suitable for children
under 36 months, due to a lack of extra safety precautions and taking into account the limited mental capac-
ities of toddlers. For Bronco 1.0m and 1.5m it should be deliberately made diffi cult to access the play equip-
ment, because of a lack of extra safety precautions and the risk of falling. To achieve this diffi cult access, you
can use a step (higher than 60 cm), or a ladder with a fi rst step higher than 40 cm.
4. This product meets all security aspects of the European standards EN1176-1&3:2017. It is fi t for use in com-
mercial playgrounds, both indoor and outdoor.
5. The product must be installed onto a playground equipment (eg a wooden play tower).
6. The assembly must be carried out in such a way that the construction supports the weight at all times and that
head, fi nger and clothing entrapments are excluded as described in EN1176. Use the toggle test in order to
prevent fi nger and/or clothing entrapments during gliding, there should be no openings around the platform
between 8 mm and 25 mm wide. To prevent neck entrapment the distance between the balustrade and the
slide should be smaller than 45 mm.
7. When mounting the product, attention should be given to the minimum required distance between the slide
and eventual obstacles: walls, fencing, etc... Since this is a slide type 1 the distance (safety area behind the
slide) should be a minimum of 2000 mm for Bronco 1.5m and Bronco 1.0m or 1500mm for Bronco 0.6m (FIG
I). There cannot be an overlapping of surrounding safety areas because sliding is a forced movement. The
higher the slide is placed, the larger the safety zone becomes. The safety area must have a radius of 1000 mm
and a height of 1500 mm.
8. In this safety area there should be no hard, angular or pointed objects. The surface underneath the slide
should be fl at and shock absorbent, with impact attenuation at least equivalent to a free height of fall of 1m.
The slide cannot be placed on asphalt, concrete or any other hard surface. At the bottom end of the slide a
soft impact attenuating surface needs to be in place (rubber tiles, tree bark, wood pieces, sand, gravel, rubber
wet pour) which stretches at least 1 m around the run-out section.
9. See notes at the rear of the slide for the recommended platform height. The slide must be mounted only onto
this recommended platform height (+/- 5 cm). A cross bar must be in place in front of the opening of the slide
at a height of between 600 mm and 900 mm above the starting point (FIG II).
10. The maximum tolerated falling height for the slide (type 444.015) is 1.5 m, 1 m for type 444.010, and 0.6 m
for type 444.006. This is measured from the ground up to the highest point of the slide where children can sit.
11. The ground level surface must be suffi ciently stable to avoid subsidence and to ensure that the slide does not
get damaged.
12. It is strongly advised not to lift the slide from the bottom end after it has been fi xed to the platform. This will
damage and/or break the slide. The slide is anchored at the bottom – this anchor needs to be set in concrete.
13. To avoid the slide heats up, do not place them facing the sun. In warm weather, check that the slide is not too
hot.
INSPECTION AND MAINTENANCE
The frequency of inspection and maintenance will vary with the type of equipment or materials used or other factors
(e.g. heavy use, levels of vandalism, coastal location, air pollution, age of equipment, ...). The frequency of the
inspection checks should be increased according to the occurrence of special factors.
Replacement parts should conform to KBT specifi cations. Check the levels of the impact attenuating surfaces when
they consist of loose fi lling materials.
Routine visual inspection (weekly to monthly)
- Always check that the bolts and nuts are securely fastened.
- Check the shock absorbing surface for objects that don't belong there.
- Check for missing parts.
- Check the equipment ground clearances.
Operational inspection (1 to 3 months)
- Check the stability of the construction.
- Check every part for excessive wear and replace when necessary.
Annual inspection (1 to 2 times per year)
- Check for rust and corrosion.
- Check every part for excessive wear and replace when necessary.
2
rotomoulded slide 'Bronco'
EN
4
min.
70 mm
min.
75 mm
ASSEMBLY - MONTAGE - MONTAJE - MONTAGGIO - MONTAŻ
ASSEMBLY - MONTAGE - MONTAJE
MONTAGGIO - MONTAŻ
1
2
(444.006.) h 0,6 m: 1120 mm
(444.010.) h 1,0 m: 1630 mm
(444.015.) h 1,5 m: 2320 mm
a
min.
200 mm
70 mm
200 mm
175 mm (0.6 m)
175 mm (0.6 m)
min.
75 mm
min. 540 mm
min. 500 mm (0.6 m)
c
Instructions for use - M444.07 - rotomoulded slide 'Bronco'
3
b
x
11
Publicité
