Optional Accessory - DeWalt DCE800 Guide D'utilisation

English
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Attaching Sanding Discs (Fig. D)
Your DCE800 drywall sander is designed to use 9" (225 mm)
sanding discs 10 . Sanding discs for the DCE800 attach with
hook and loop.
The recommended sanding discs are available at extra cost
from your local dealer or authorized D
To Attach Sanding Disc to the Sanding
Pad (Fig. D)
1. Turn the sander over so that the sanding pad
facing upward.
2. Clean the dust from the sanding pad face.
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, center and place the sanding
disc 10 directly on top of the pad.
Speed Control Dial (Fig. A)
The DCE800 Sander is equipped with variable speed control.
Adjust the speed by turning the speed control dial
speed control dial is numbered "1" through "7". The setting
"1" is the slowest speed (approximately 700 RPM) and "7" is
the fastest speed (approximately 1200 RPM).
Use the higher speed settings for fast stock removal. Use
the lower speed setting to reduce removal rate for more
precise control.
Brush-Type Skirt (Fig. D)
A brush-type skirt surrounds the abrasive pad on the
11
DCE800. This skirt serves two purposes:
• It extends below the surface of the abrasive pad to
prevent the abrasive from "gouging" the work.
• It helps contain the drywall dust until the vacuum
cleaner pulls it away.
If the skirt is damaged or if it is worn excessively it should be
replaced by a D WALT authorized service center.
e
Expanding the Main Tube (Fig. F)
The main tube of the DCE800 can be expanded to various
desired lengths.
• To exapnd the main tube, release the tube expansion
lever 8 and extend the tube to the desired length.
10
•
Attaching an AirLock
Extractor (Fig. G, H)
Your drywall sander is compatible with the D
AirLock™ connection system. The AirLock™ allows for a fast,
secure connection between the AirLock™ connector
and sander's dust extraction port
1. Ensure the collar on the AirLock™ connector is in the
2. Push the AirLock™ connector onto the adapter
3. Rotate the collar to the locked position.
WALT service center.
e
Wireless Tool Control (Fig. A)

9 is
Your sander is equipped with a Wireless Tool Control
transmitter which allows your sander to be wirelessly
paired with another Wireless Tool Control device, such as a
dust extractor.
To pair your sander using Wireless Tool Control, slide
the ON/OFF slider switch
Wireless Tool Control pairing button on the seperate device.
4 . The
An LED on the seperate device will let you know when your
sander has been successfully paired.
D
(Fig. A, I)

Optional Accessory




Your tool comes with mounting holes
for installing a D
will need a cross head bit tip to install the tag. Screw torque
should be between 0.8 and 1.2 Nm (7.1 to 10.6 in-lbs). The
D
e
professional power tools, equipment, and machines using
the D
the D
To learn more, visit:
www.D
Close the tube expansion lever to lock the main tube
in place.
™
unlock position. (Refer to Figure G.) Align notches
on collar and AirLock™ connector as shown for unlock
and lock positions.
connector point.
nOTE: The ball bearings inside collar lock into slot and
secure the connection.The power tool is now securely
connected to the dust extractor.
nOTE: The sleeve of the dust extraction port can
16
be removed if damaged and replaced by the user. The
sleeve is available as an optional accessory and can be
replaced using a screwdriver.
CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the sander.
3 on the sander and press the
WALT Bluetooth® Tool Tag Ready
e
WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.
WARNING: Remove battery from tool before installing
the D WALT Bluetooth® Tool Tag.
e
WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be
sure to securely tighten the screws.
WALT Bluetooth® Tool Tag (DCE041). You
e
WALT Tool Tag is designed for tracking and locating
WALT Tool Connect™ app. For proper installation of
e
WALT Tool Tag, refer to the D
e
WALT.com/en-us/jobsite-solutions/tool-connect
e
Compatible Dust
WALT
e
12
7 .
13
WALT
e
WALT
e
14 and fasteners 15
WALT Tool Tag manual.
e