Télécharger Imprimer la page

TEKTELIC COMMUNICATIONS Kona Micro Gateway Mode D'emploi

Masquer les pouces Voir aussi pour Kona Micro Gateway:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

TEKTELIC C
Document type:
Document number:
Document version:
Document Status:
Product name:
Product codes:
TEKTELIC Communications Inc.
th
7657 10
Street NE
Calgary, AB, Canada T2E 8X2
Phone: (403) 338-6900
© 2019 TEKTELIC Communications Inc., All rights reserved.
All products, names and services are trademarks and registered trademarks of their respective companies.
Disclaimer:
Material contained in this document is subject to change without notice. The material herein is solely for
information purposes and does not represent a commitment by TEKTELIC or its representatives. TEKTELIC has
prepared the information contained in this document solely for use by its employees, agents, and customers.
Dissemination of this information and/or concepts to other parties is prohibited without the prior written consent
of TEKTELIC. In no event will TEKTELIC be liable for any incidental or consequential damage in connection with the
furnishing, performance or use of this material.
TEKTELIC reserves the right to revise this publication in accordance with formal change control procedures defined
by TEKTELIC.
OMMUNICATIONS
User Guide
T0005281_UG
1.2
Approved
Kona Micro Gateway
See Table 1
I
.
NC

Publicité

loading

Sommaire des Matières pour TEKTELIC COMMUNICATIONS Kona Micro Gateway

  • Page 1 Street NE Calgary, AB, Canada T2E 8X2 Phone: (403) 338-6900 © 2019 TEKTELIC Communications Inc., All rights reserved. All products, names and services are trademarks and registered trademarks of their respective companies. Disclaimer: Material contained in this document is subject to change without notice. The material herein is solely for information purposes and does not represent a commitment by TEKTELIC or its representatives.
  • Page 2 Jun. 11, 2019 Approved S. Morrison Added models T0006271 & T0006342 Dec. 9, 2019 Approved Added Proposition 65 Statements Herasymiuk Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 2 of 29...
  • Page 3 Specifications........................7 Installation ..........................9 2.1. Overview .......................... 9 2.2. Unpacking and Inspection ....................9 2.3. Kona Micro Gateway Mounting ..................9 2.4. DC Power Cable Installation ................... 11 2.5. Battery Installation ......................12 2.6. RF Cable Installation ....................... 13 2.7.
  • Page 4 1. Product Description 1.1. Overview The Kona Micro Gateway is a LoRaWAN IoT gateway that supports the full range of LoRa WAN channels. The Gateway supports one external LoRa antenna, copper Ethernet backhaul, and optional 3G/4G wireless backhaul. All Gateway models are powering from an AC-DC power adapter and may optionally have an internal backup battery provisioned.
  • Page 5 T0005238 Australia (Tern) 915-933 T0005239 Figure 1 illustrates the Kona Micro Gateway external form-factor with the front view on the top and rear view on the bottom. All models share the same mechanical form-factor. Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc.
  • Page 6 Figure 1: Kona Micro Gateway Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 6 of 29...
  • Page 7 1.2. Physical Interfaces Figure 2 illustrates the connector layout for the Kona Micro Gateway. Ethernet LoRa RF DC Power Antenna Figure 2: Kona Micro Gateway Bulkhead Layout The Gateway connectors are listed in Table 2. Table 2: Kona Micro Gateway Interface Connector Types...
  • Page 8 Table 3: Kona Micro Gateway Specifications Attribute Specification Dimensions 120 (L) x 118 (W) x 41.5 (H) mm Weight 336 g (0.74 lbs) with battery, 245 g (0.54 lbs) without battery 0°C to 40°C without battery Operating Temperature 0°C to 38°C with battery...
  • Page 9 2.3. Kona Micro Gateway Mounting Kona Micro Gateway can be placed on a flat surface or can be mounted to a wall with M3 screws to locations on the back of the module illustrated in Figure 3.
  • Page 10 Mounting screw location Figure 3: Kona Micro Gateway Mounting Screw Locations While wall mounted, the Gateway module must be oriented with the TEKTELIC logo horizontal, parallel to the earth as shown in Figure 4. Kona Micro User Guide T0005281_UG Version 1.2...
  • Page 11 2. Install 2 site supplied M3 screws into the wall at 60 mm (2.4”) center spacing, leaving the screw heads protruding with a 3 mm gap from the wall surface. 3. Hang the Kona Micro Gateway by mounting the two to keyhole slots onto the screws. 2.4. DC Power Cable Installation The Kona Micro Gateway is powered from the supplied AC-DC power adaptor.
  • Page 12 Figure 5: DC Power Connection Polarity 2.5. Battery Installation Use only a battery provided by Tektelic Communications Inc. Dispose of old batteries in accordance with regulatory requirements. Remove the battery cover by removing the two Torx- drive battery cover securement screws. Connect the 3-pin battery connector to the connector at the bottom of the battery compartment and then insert the battery into the battery compartment as illustrated in Figure 6.
  • Page 13 Note that the 3G/4G modem antenna is internal to the Kona Micro Gateway. 2.7. Copper Ethernet Cable Installation The Kona Micro Gateway Ethernet port may be used on a temporary basis for commissioning and maintenance or may be permanently connected for backhaul.
  • Page 14 Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 14 of 29...
  • Page 15 2.7 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Antenna: ET830DBLTRPSMA – Airgain, Inc. Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 15 of 29...
  • Page 16 Before servicing the product, the antenna(s) or cables, turn off the transmission function or the unit power if you have to get closer than the minimum separation distance. Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 16 of 29...
  • Page 17 4. Description du produit 4.1. Aperçu Le Kona micro Gateway est une passerelle intérieure LoRaWAN ITO qui prend en charge la gamme complète des canaux de Lora WAN. La passerelle prend en charge une antenne Lora externe, un câble Ethernet en cuivre et une connexion sans fil 3G/4G en option. Tous les modèles Gateway sont alimentés à...
  • Page 18 915-933 T0005239 La figure 7 illustre le facteur de forme externe Kona Micro Gateway avec la vue de face en haut et la vue arrière en bas. Tous les modèles partagent le même facteur de forme mécanique. Kona Micro User Guide T0005281_UG Version 1.2...
  • Page 19 Figure 7: Passerelle intérieure Kona Micro Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 19 of 29...
  • Page 20 4.2. Interfaces physiques Figure 8 illustre la disposition de la cloison de la Kona Micro Gateway. Ethernet LoRa RF DC Power Antenna Figure 8: Kona Micro Gateway Mise en page de cloison Les connecteurs de la passerelle intérieure sont répertoriés dans Table 5.
  • Page 21 Table 6: Kona Micro Gateway Spécifications Attribute Spécifications Dimensions 120 (L) x 118 (W) x 41.5 (H) mm Poids 336 g (0.74 lbs) avec batterie, 245 g (0.54 lbs) sans batterie 0°C to 40°C sans batterie Température de fonctionnement 0°C to 38°C avec batterie Humidité...
  • Page 22 • Toutes les pratiques d'installation doivent être conformes aux codes électriques locaux et nationaux. • Assurez-vous que la Kona Micro Gateway est située de façon à éliminer tout risque physique pour les personnes ou les biens. • La passerelle interne Kona Micro doit être alimentée par l'adaptateur secteur CA-CC fourni.
  • Page 23 5.3. Kona Micro Gateway Montage Kona Micro Gateway peut être placé sur une surface plane ou peut être fixé à un mur avec des vis M3 à l'arrière du module illustré à la Figure 9. Emplacement de la Emplacement de...
  • Page 24 2. Installez 2 vis M3 fournies dans le mur à un espacement central de 60 mm (2,4 "), en laissant les têtes de vis dépasser d'un espace de 3 mm de la surface de la paroi. 3. Accrochez la Kona Micro Gateway en montant les deux fentes en trou de serrure sur les vis.
  • Page 25 Figure 11: Polarité directe du connecteur d'alimentation CC 5.5. Battery Installation Utilisez uniquement une batterie fournie par Tektelic Communications Inc. Éliminez les batteries usagées conformément aux exigences réglementaires. Retirez le couvercle de la batterie en retirant les deux vis de fixation du couvercle de la batterie du lecteur Torx. Branchez le connecteur de la batterie à...
  • Page 26 Figure 12: Battery Installation Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 26 of 29...
  • Page 27 · lbs. Le Kona micro n'est pas protégé contre les surtensions d'éclairage car il est destiné à une utilisation à l'intérieur. Ne pas raccorder à une antenne extérieure. Notez que l'antenne du modem 3G / 4G est interne à la Kona Micro Gateway. 5.7. Installation du câble Ethernet en cuivre Le port Ethernet Kona Micro Gateway peut être utilisé...
  • Page 28 à 2,7 dBi sont strictement interdites pour cet appareil. L'impédance d'antenne requise est de 50 ohms. Antenne: ET830DBLTRPSMA - Airgain, Inc .. Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 28 of 29...
  • Page 29 Avant de réparer le produit, l'antenne ou les câbles, désactivez la fonction de transmission ou l'alimentation de l'unité si vous devez vous rapprocher de la distance de séparation minimale. Kona Micro User Guide T0005281_UG Version 1.2 TEKTELIC Communications Inc. Confidential Page 29 of 29...