Publicité
This document describes the 15 essential steps to follow in order to have an optionally-functioning camera. For more
details however, please consult the VSS User Guide and the Camera Installation Guide, both available on my.survision.fr.
1
Download the VSS application from our site my.survision.fr. For this,
input the ID and password provided by SURVISION, and then go to
the "Software" tab.
If you do not know, or have lost your access details, please contact:
support@survision.fr.
2
Install VSS on your computer. The minimum required speci cation
is Windows XP.
3
Install your SURVISION equipment using the mechanical parts
provided.
4
Connect the power supply cable provided to the power supply unit.
The brown or red wire corresponds to the
or black wire to the
terminal. The power supply may be either 12
or 24 volts (see the sticker on the back of the camera: polarity and
voltage indications must imperatively be complied with). The
cabling should be completed as soon as the camera is installed, in
C
order to ensure that it will be waterproof.
M
Y
CM
MY
CY
CMY
K
5
Fit the Ethernet connector provided onto an Ethernet cable and
connect it all to the camera. See the "Ethernet Connector
Installation" sheet. The connector must be correctly tted in order
to ensure waterproofness.
6
Connect the camera to your computer, either directly by means of
the Ethernet cable, or, if the camera is on a local network, by
connecting the computer to a switch of this network. Con gure a
xed IP address for your network card within the range 192.168.0.X.
7
Start the VSS. Each camera is represented by a line on the screen on
which you double click to connect to the camera.
8
Place a vehicle or plate at the centre of the desired recognition
zone. Display the grill on the VSS and direct the camera in such a
way that the plate is both horizontal and at the centre of the image.
SURVISION
118, avenue Paul Doumer
FR 92500 RUEIL-MALMAISON
Tél. : +33 (0)1 47 51 04 80
Fax : +33 (0)1 57 69 15 80
SIRET : RCS Toulouse 439 931 031 00058
www.survision.eu
SHORT INSTALLATION GUIDE
For MICROPAK and NANOPAK ANPR cameras
terminal, and the blue
etiquette_mp.pdf 1 17/09/2013 14:00:23
118 avenue Paul Doumer
92500 Rueil-Malmaison - FRANCE
www.survision.fr
9
Adjust the camera zoom ("Camera" tab) in such a way that the plate
measures a minimum of 130 pixels and a maximum of 170 pixels,
measured from the left side of the rst character to the right side of
the last character.
10
Adjust the focus by clicking on "Detect focus" ("Camera" tab).
11
Adjust the power of the LEDs ("Camera" tab):
- 500 mA for a distance of less than 5 meters
- 1,000 mA for a distance between 5 and 10 meters
- 1,500 mA for a distance between 10 and 15 meters
- 2,000 mA for a distance of more than 15 meters
12
Choose the most appropriate enslavement for the situation
("Settings" tab, "Enslavement" menu, "Edit"):
- Urban Free Flow: for an application in urban zones or in non-stop
toll lanes (<50 km/h)
- Free Flow: for a road application where the vehicles are unlikely to
stop in the image (> 50 km/h)
- Access Control: for an access control application (the vehicles stop
momentarily on the screen)
13
Select the geographic installation zone of the camera ("Settings"
tab, "ANPR" menu, "Edit") and indicate whether you also want to
recognise foreign plates.
14
The camera adjustment is now complete. Save the con guration on
an XML le ("Settings" menu, "Save Con guration to File") and save
a recognition image ("Detections" tab, click on "View" and then on
"Save") and push these two elements onto our site my.survision.fr
by connecting them to the camera which has been adjusted
correspondingly
15
Close the VSS while waiting for the camera to disconnect
completely.
160 PX
Publicité
