Publicité
Introduction
Description
Technical data
Usage limits (IEC 60974-1)
How to lift up the machine
Open the packaging
Installation
Connection to the electrical supply
Usage norms
MMA electrode welding (Fig. B)
TIG welding (Fig. C)
Maintenance
The pointing out of any difficulties and their elimination 5
Procedure for welder assembly and disassembly
D I N S E G . m . b . H .
Tarpen 36 • D-22419 Hamburg
Tel. +49 (0)40 658 75-0
Fax +49 (0)40 658 75-200
info@dinse.eu – www.dinse.eu
Copyright © 2018 DINSE G.m.b.H., Hamburg.
These instructions or excerpts there of shall not be duplicated, transla-
ted or reproduced, nor shall they be stored, processed, transmitted or
distributed by any electronic means without the prior written permission
of DINSE G.m.b.H.
Introduction
1
Thank you for purchasing one of our products. Please read in-
1
structions on use in this manual as well as the safety rules
given in the attached booklet and follow them carefully to get
2
the best performance from the plant and be sure that the parts
have the longest service life possible. In the interest of custom-
2
ers, you are recommended to have maintenance and, where
necessary, repairs carried out by the workshops of our service
2
organisation, since they have suitable equipment and specially
trained personnel available. All our machinery and systems are
2
subject to continual development. We must therefore reserve
the right to modify their construction and properties.
2
2
Description
3
DIX GO is the latest evolution in inverter technology genera-
tors for welding. The most advanced materials and components
3
have been used to design and produce it such as:
• Main planar transformer with extremely low load loss.
4
• Electronic auxiliary feeder.
• Voltage doubler ensuring precision striking, constant arc and
5
very low electrical input from the main supply by the welder.
• Extremely high frequency power INVERTER with very lat-
est type of IGBT to reduce switching losses to a minimum.
• The inverter resists ample current variations (MAX 290V) and
5
can be utilized with very long electric cables (MAX 100 m).
• Selector with 3 weld procedures:
- Basic electrodes with "Hot Start" and "Arc Force" device.
- Stainless steel electrodes with special characteristics for
a soft arc.
- TIG welding with thermal controlled (TCS) "Lift" type strik-
ing reducing tungsten inclusions to a minimum and allow-
ing to also strike on sharp edges.
• The generator also conforms to all European Union stand-
ards and directives in force.
Model
Single-phase power supply 50/60 Hz
Mains supply: Z
(*)
max
Power input @ I
Max
2
Delayed fuse (I
@ 100%)
2
Power factor / cosφ
Maximum efficiency degree
Open circuit voltage (max)
Current range
Duty cycle @ 100% (40°C)
Duty cycle @ 60% (40°C)
Duty cycle @ 20% (40°C)
Usable electrodes
Standards
Insulation class
Protection class
Dimensions
Weight
(*) Mains supply Z
: maximum impedance value allowed for the grid
max
according to the EN/IEC 61000-3-11 standard.
WARNING: This equipment does not comply with EN/IEC 61000-3-12.
If it is connected to a public low voltage system, it is the responsibil-
ity of the installer or user of the equipment to ensure, by consultation
with the distribution network operator if necessary, that the equipment
may be connected.
2
Table 1
DIX GO 1306.M
V
230
Ω
0,19
kVA
11,3
A
20
0,59 / 0,99
η
0,74
V
88
A
5 ÷ 180
A
110
A
130
A
180
Ø mm
1,6 ÷ 4
IEC 60974-1
IEC 60974-10
IP 23 S
F
mm
390-300-135
kg
6
Publicité
