Publicité
USE INSTRUTIONS MINI-SAFE FOR KEYS WITH ELECTRONIC COMBINATION Model KG/4E
•
The mini-safe for keys is supplied with the door open, the factory personal combination
0 – 0 – 0 – 0 – 0 – 0
•
The mastercode is a code that the owner
(PIN) is forgotten.
•
Preserve the personal combination and mastercode in a safe place.
•
If the mini-safe is not used for a long time, it is advisable to remove the batteries.
•
The CLEAR
is used to cancel the last incorrectly entered digit.
INITIAL SETTINGS AND OPENING THE DOOR:
•
Open the protective flap by pressing on the sides and pulling to access the keypad.
•
Open the door and unscrew the screw locking the battery compartment cover.
•
Insert 3 alkaline 1,5V AAA batteries respecting the correct polarity, replace the battery compartment cover and tighten the screw.
•
Remove the yellow protective tab from its seat (fig.1).
•
Perform a test opening with the door open by digiting the factory combination
heard and the green light will light up for a few seconds).
SETTING THE PERSONAL COMBINATION:
•
Press the little
RESET
(pic.1) located inside the door (two beeps will be heard and the green light will light up).
•
With the green light on, digit your personal combination
•
Repeat the combination previously entered and press the
•
The acoustic signal of two beeps and the green light switching off indicate that your personal combination has been memorized correctly;
•
In the event of error, repeat the setting operation from the beginning.
IMPORTANT: Before closing the door carry out some opening tests.
SETTING THE NEW MASTERCODE COMBINATION:
•
0
Press twice the "
" key and press the little
•
Within 10 seconds, enter the Master code that was previously programmed (for a new mini safe 0-0-0-0-0-0) and press the
will be heard).
•
Digit your new Master code
•
Re-enter the new Master code and press the
•
The acoustic signal of two beeps and the green light switching off indicate that your mastercode combination has been memorized correctly.
•
In the event of error, repeat the setting operation from the beginning.
IMPORTANT: Before closing the
OPENING THE DOOR:
•
Digit the personal combination you have set and press the
pull the door straight away to release it from the internal catch.
❖
In the event of 3 consecutive errors in digiting the personal combination, the keypad will lock for 20 seconds. Should 3 more consecutive
incorrect entries be made, the keypad will lock for 5 minutes.
CLOSING THE DOOR:
•
Close the door by pushing it till it clicks on the internal catch.
WALL INSTALLATION:
•
Chose the fixing position, open the door and, keeping the safe vertical, mark the position of the 4 holes on the wall;
•
Use a Ø 6mm drill to drill the 4 holes about 30mm.deep;
•
Insert the 4 plugs into the holes drilled in the wall;
•
Position the mini-safe accurately, insert the screws from the inside and screw into the relevant plugs.
LOW BATTERIES SIGNAL:
•
The red light lighting up after the opening procedure indicates that the batteries inside are being exhausted. Replace the batteries as soon as
possible.
•
Almost totally discharged batteries will trigger a continuous beep with the simultaneous switching on of the green LED not unlocking the
door.
OPENING THE DOOR WHEN THE BATTERIES INSIDE ARE COMPLETELY EXHAUSTED:
Using the battery holder for 3 1,5V AAA batteries supplied, proceed as follows:
•
Remove the small black rubber plug located at the outer bottom of the mini-safe;
•
Install 3 new alkaline 1,5V AAA batteries, respecting the polarity;
•
Insert the mini-USB of the battery holder into the mini-safe USB port (see pic. 2) and turn it on by bringing the lever to ON;
•
Digit the personal combination you have set and press the
•
With the green light on, open the door and proceed to the replacement of the batteries inside
Istr. KG-4E_2023_mastercode
MUST
personalize with his own secret code in order to be able to open the door if the user code
from 4 to 8 digits
#
"RESET"
(pic.1) located inside the door (three beeps will be heard and the green light will light up).
from 4 to 8 digits
and press the
#
key.
door,
carry out some opening tests.
#
#
1 – 2 – 3 – 4 – 5 – 6
1 – 2 – 3 – 4 – 5 – 6
#
and press the
key;
#
key (two beeps will be heard).
key (two beeps will be heard and the green light will light up for a few seconds) and
key (two beeps will be heard and the green light will light up).
and with the factory mastercode
#
and pressing the
key (two beeps will be
key (two beeps will be heard).
.
#
key (two beeps
Publicité
