Armacost Lighting 513125 Guide Rapide

ProLine CCT Tunable White
LED Controller
With RF Remote Control
Model # 513125
Introduction
This LED controller is designed to work with constant voltage
CCT Tunable White LED products such as LED tape light or
LED fixtures in a voltage range of 12–24 volts DC. The receiver
works with the RF wireless remote control, which allows the
user to adjust LED brightness and select color temperature.
Receiver & wiring
87mm
72mm
1 3 2
1. Input – from power supply
The controller input and output voltage range is 12–24 volts DC.
Make sure the LED lighting voltage is within this range and below
the rated wattage of the power supply. Connect input wires
from the power supply to the controller as indicated by the
polarity markings on the controller (+ to + and – to –).
2. Output – to LED lighting
Observe polarity indicated on the controller when
connecting to LED lighting (+ to + and – to –).
Make sure the voltage of the LED lighting is the same as the power
supply and the maximum load doesn't exceed that of the controller.
CAUTION: Shorting of output cables could cause permanent damage
to controller. Make sure cables are well insulated from each other.
3. Controller status indicator
This light shows the working status of the controller.
It shows different events as following:
Steady green: Normal operation
Single green blink: Command received
Long single green blink: Mode or color cycle edge
Long single yellow blink: Reach brightness limit
Red flash: Overload protection
Yellow flash: Overheat protection
Green flash 3 times: New remote controller paired
4. Wiring diagram
Connect the power supply to the controller input and the controller
output to the LED lighting. The output voltage of the power supply
must be the same as the voltage of the LED lighting. Make sure all
power cables are conected securely and insulated before powering on.
12–24V DC
100/230V
AC Power Power Supply
Remote Control
5. On
Press to turn controller on.
6. Off
Press to turn controller off. The
controller will remember the controller
state when powered off, and will return
to that state when powered back on.
7. Color selection
Cycles through color temperatures.
24mm
8. Favorites
When on a selected color press and
hold to set that color to one of the
four buttons.
9. Brightness control
Press to increase LED brightness and
press to decrease it.
10. Remote indicator
When pressing keys, the indicator blinks if the remote is working
properly. If the indicator flashes slowly when pressing keys, battery power
is low and it needs to be replaced. Replace with a CR2032 battery.
Remote control operation
11. Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote
will work through walls and doors. Do not install in a metal enclosure.
12. Pairing with a new remote control
The remote control and receiver are already paired,
but up to five remotes can be paired to one receiver.
To pair a new remote:
1. Unplug power to receiver and wait five seconds.
2. Reconnect power and within ten seconds press the ON and
keys simultaneously until the remote indicator flashes quickly.
13. De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using
with the controller and any other paired remotes will be de-paired.
Output LED LED
Controller Lighting
12–24V DC 12–24V DC
5
6
7
8
Safety Protection
The controller has a function to prevent it from being damaged
by mis-wiring, output short circuit, overloading, or overheating.
It will automatically shut down under these extreme conditions
until safe operating conditions are restored. To avoid shutdowns,
make sure the installed LED lighting is compatible with constant
voltage, is in the rated range of the controller, and the cables
are well connected and insulated. Also, install the controller
with proper ventilation and heat dissipation in mind.
Specifications
Output mode ................................................... PWM constant voltage
Working voltage .............................................................. 12–24V DC
Rated output current .............................................................. 1x10A
10
Brightness grade .................................................................11 levels
PWM frequency .......................................................................1KHz
9
PWM physical grade .......................................................... 256 steps
Overload protection ..................................................................... yes
Overheat protection ..................................................................... yes
Remote frequency .......................................................... 433.92MHz
Remote control range ......................... up to 50 ft./ 15m in open areas
Controller dimensions ........ 3.43 X 0.95 X 0.59 in. / 87 X 24 X 15mm
Remote dimensions ............. 5.27 X 1.4 X 0.38 in./ 134 X 36 X95mm
Customer support
Email: support@armacostlighting.com
Phone: 410-354-6000
Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
3-year limited warranty. This product is for dry location use only.
Improper installation, improper powering, abuse, or failure to use this
device for its intended purpose will void warranty. Proof of purchase is
required for all returns. Questions? Email support@armacostlighting.com.
armacostlighting.com
© 2022 Armacost Lighting.
All rights reserved.
221201