Publicité
Bizonyos problémák elhárítása
1. A készülék nem működik:
a. Kérjük, ellenőrizze a tápegység és a vevő csatlakozását.
b. Kérjük, ellenőrizze a címzettet.
c. Ellenőrizze az érzékelő és a környezeti fény beállításait.
2. Alacsony érzékenység:
a. Kérjük, ellenőrizze, hogy nincsenek-e olyan eszközök az érzékelő előtt, amelyek zavarhatják a vett jeleket.
b. Kérjük, ellenőrizze a környezeti hőmérsékletet.
c. Győződjön meg arról, hogy az észlelni kívánt objektum az észlelési mezőn belül van.
d. Kérjük, ellenőrizze, hogy a beépítési magasság megfelel-e az ajánlásoknak.
e. Kérjük, ellenőrizze, hogy az érzékelő pozícióbeállítása helyes-e.
3. Az érzékelő nem tudja automatikusan kikapcsolni a terhelést:
a. Kérjük, ellenőrizze, hogy vannak-e folyamatos mozgásjelek az érzékelési területen.
b. Kérjük, ellenőrizze, hogy az időkésleltetés nincs-e a leghosszabb értékre állítva.
c. Kérjük, ellenőrizze, hogy a tápellátás megfel az előírtaknak
PIRYT LED garden luminaire with motion sensor
EN
Operating instruction
Directions for safety use
Before using the device, read this Operating Instruction and keep it for future use. Any repair or modification carried out by yourselves results in loss
of guarantee. The manufacturer is not responsible for any damage that can result from improper device installation or operation. Installation of the device
should be carried out by an experienced person familiar with the relevant installation regulations in force in the country concerned or by an electrician. In
view of the fact that the technical data are subject to continuous modifications, the manufacturer reserves a right to make changes to the product
characteristics and to introduce different constructional solutions without deterioration of the product parameters or functional quality. Additional
information and technical support related to the product is available at www.adviti.pl. Orno-Logistic Sp. z o.o. holds no responsibility for the results of non-
compliance with the provisions of the present Manual. Orno Logistic Sp. z o.o. reserves the right to make changes to the Manual - the latest version of the
Manual can be downloaded from support.adviti.pl. Any translation/interpretation rights and copyright in relation to this Manual are reserved.
1. Disconnect power supply before any activities on the product.
2. Do not immerse the device in water or other liquids.
3. Do not cover the device during its operation.
4. Do not operate the device when its housing is damaged.
5. Do not open the device and do not repair it by yourselves.
6. Do not use the device contrary to its dedication.
7. The product cannot be dismantled. If the light source is damaged, it cannot be repaired.
8. The chipped globe, screen or protective shield must be replaced immediately.
9. The minimal distance of a light fixture (its light source) from the spots and objects that it's illuminating.
10. Risk of electric shock.
11. The product is not compatible with lighting dimmers.
12. Do not look at LEDs directly from up close.
13. Product compliant with CE standards.
14.Protection class II.
15. The product is suitable for indoor and outdoor use.
16. Recycling information. Each household is a user of electrical and electronic equipment, and hence a potential producer of hazardous waste for humans
and the environment, due to the presence of hazardous substances, mixtures and components in the equipment. On the other hand, used equipment
is valuable material from which we can recover raw materials such as copper, tin, glass, iron and others. The WEEE sign placed on the equipment, packaging
or documents attached to it indicates the need for selective collection of waste electrical and electronic equipment. Products so marked, under penalty of
fine, cannot be thrown into ordinary garbage along with other waste. The marking means at the same time that the equipment was placed on the market
after August 13, 2005. It is the responsibility of the user to hand the used equipment to a designated collection point for proper processing. Used equipment
can also be handed over to the seller, if one buys a new product in an amount not greater than the new purchased equipment of the same type. Information
on the available collection system of waste electrical equipment can be found in the information desk of the store and in the municipal office or district
office. Proper handling of used equipment prevents negative consequences for the environment and human health!
Important information before installation
The following criteria should be taken into account when choosing the installation site:
- avoid installing on uneven surfaces,
- the sensor should not be directed at brightly lit objects (i.e. white) or objects that are a source of heat, as these may adversely affect the operation,
- do not install near strong sources of electromagnetic interference,
- do not install in front of highly reflective surfaces e.g. mirrors, windows etc,
- do not place the lamp near objects that can be moved by strong wind (trees, bushes, curtains, etc.),
- ensure that supply cables have adequate current protection in the form of suitable fuses or other devices to cut off the power supply in the event of an overload,
- contamination of the sensor optics causes the range and sensitivity of motion detection to decrease.
Intended use/purpose
The garden luminaire is characterized by high durability and quality. Placed on the facades of buildings or concrete fences in the gardens, it creates a unique
lighting scene. The modern SMD LEDs used guarantee high energy efficiency and a long life of the device. Equipped with a passive infrared sensor that
reacts when motion appears in the detection field, and the twilight sensor (depending on the settings) switches on the lighti ng only when it is needed.
Potentiometers for adjusting: lighting time and light intensity.
Installation
1. Switch off the power.
2. Prepare the equipment needed for installation.
3. Unscrew the screw and separate the lamp from the base.
4. Pull the wires through the hole in the base and connect the wires according to the diagram
5. Drill holes in the wall and screw the base to the desired location using screws.
6. Attach the lamp to the base of the plafond.
7. Switch on the power and test it.
4
Publicité
