Télécharger Imprimer la page

Publicité

Liens rapides

Parts List
NAV102 navigation module
ü
Antenna with magnetic mount
ü
Four rubber feet (to affix to the bottom of the NAV102 in the
ü
recessed area near each corner)
SmartBus cable (used to connect the NAV102 to the Jensen
ü
navigation-ready radio)
One 2 Gigabyte SD Card pre loaded with map/navigation
ü
software
Two 11mm (.4in) screws (for fastening the SmartBus cable
ü
to the radio and NAV102)
DVD with backup software for map data and navigation
ü
Warnings
Do not install components in areas which are susceptible to
Ÿ
rain, moisture, direct sunlight, extreme heat or cold,
excessive dust, dirt or humidity.
Do not install the NAV102 where it will obstruct the driver's
Ÿ
view or interfere with the vehicle's operating system or
safety features (air bags, hazard light buttons, etc.).
Use only installation parts and hardware provided with the
Ÿ
unit. Use of other parts can cause malfunction and possible
damage to your navigation system.
This product should only be installed in vehicles with a 12-
Ÿ
volt battery with negative grounding. Check the battery
voltage of your vehicle before installation.
Be sure to secure all wires/cables safely away from the
Ÿ
steering wheel, shift lever, and gas or brake pedal.
Do not cut the GPS antenna cable to shorten or lengthen it.
Ÿ
All manuals and user guides at all-guides.com
NAV102 Placement
The NAV102 should be installed under the back or front seat. It
can also be installed in the trunk, if necessary. Do not install the
NAV102 where it will come in contact with water or direct
sunlight.
To avoid shorts in the electrical system, be sure to
disconnect the negative (–) battery cable before beginning
installation.
NOTE:
Be sure to install
the NAV102 in such
a way that the
SD card slot is
accessible after
install, allowing
for the removal
and insertion of
the SD card for
future changes
to map data or
upgrades.
NAV102 Installation Guide
Compatible Head Units
VM9212N
VM9213
VM9223
VM9312HD
VM9313
VM9412
AMM10N
AMM12N
VM9413
VM9423
VM9512
VM9512HD
VM9022
VM9022HD
SERIES
UV9

Publicité

loading

Sommaire des Matières pour Jensen ADVENT NAV102

  • Page 1 ü NAV102 where it will come in contact with water or direct recessed area near each corner) sunlight. SmartBus cable (used to connect the NAV102 to the Jensen ü navigation-ready radio) One 2 Gigabyte SD Card pre loaded with map/navigation ü...
  • Page 2 All manuals and user guides at all-guides.com NAV102 Wiring Diagram Insert one end of the Smartbus cable into the “DATA BUS” slot on the side of the NAV102 and secure it with a 11mm (.4in) screw (provided). Connect the other end of the cable to the NAV102 input on the back of your compatible navigation-ready head unit.
  • Page 3 área ahuecada cerca de cada esquina) agua o la luz solar directa. Cable SmartBus (usado para conectar el NAV102 a la radio ü Jensen lista para navegación) Una Tarjeta SD de 2 Gigabyte pre cargada con software de ü mapa/navegación Dos tornillos de 11mm (.4 pulgadas) (para fijar el cable...
  • Page 4 All manuals and user guides at all-guides.com NAV102 Cableado Inserte una punta del cable Smartbus dentro de la ranura "DATA BUS" en el costado del NAV102 y asegúrela con un tornillo de 11mm (0.4 pulgada) (provisto). Conecte la otra punta del cable a la entrada del NAV102 en la parte posterior de su unidad principal para navegación.
  • Page 5 Câble SmartBus (utilisé pour brancher le NAV102 à la radio ü Jensen prête pour la navigation) Une carte SD à 2 GB préchargé avec logiciel plan/navigation ü Deux écrous à 11cm (4 pouces) (pour attacher le câble SmartBus ü...
  • Page 6 All manuals and user guides at all-guides.com NAV102 câblage Insérez un bout du câble Smartbus dans la fente « DATA BUS » sur le côté du NAV102 et attachez-le avec un écrou de 11mm (.4 pouces) (fourni). Branchez l'autre bout du câble à...