Publicité
Liens rapides
T
:
HIS KIT CONTAINS
• 1 W
ALL EXTENSION
• 1 P
(
ARTS BAG
SERVICE PART NO
, 8
. 8
5/8"
CLAMP
NO
X
SCREWS
8
. 10-32
3/8"
NO
X
SCREWS
F
OLLOW HOOD INSTALLATION GUIDE STEPS
PRIOR TO WALL EXTENSION INSTALLATION
Due to the weight of this hood, ensure that the wood strip is
attached to all of the available studs (2 studs minimum for
36" width hood and 3 studs minimum for 48" or 60" width
hood); not into the wall alone.
Measure and mark a
level line on wall above
cooktop location for the
wood mounting strip.
Remove wood
mounting strip from
back of hood.
Center wood mounting
strip over location.
Use no. 10 x 2'' flat
head screws to secure
the mounting strip to
the wall.
Make sure to hit the
wall studs.
Insert house wiring through top, right hole.
Rest the back cavity of the wall extension on wood mounting
strip (provided with the hood). Secure upper portion of the wall
extension to wood mounting strip with (up to) 6 no. 8 x 5/8"
screws (included).
Drill two 3/16" diameter holes into the wall for wall anchors
through two of the existing lower holes of the wall extension.
Then, install both wall anchors, both washers and 2 no. 8 x 5/8"
screws (included).
4
6 S
TO
HD0475
2 W
ALL ANCHORS
. S97018867)
INCLUDING
, 2
, 2
WALL ANCHORS
WASHERS AND
CAUTION
HD0478A
1. Wall
4. Wall anchor location
2. Wood mounting
5. Back of wall
strip
extension outline
3. Flat head screw
6. Wall studs
CREWS
/
/
WASHERS
SCREWS
W
E
ALL
XTENSION
I
NSTALLATION
Using pliers, unfold to 90° both wall extension metal tabs to
align hood during installation.
: 1
WIRE
1
3
TO
.
HR0071
F
OLLOW HOOD INSTALLATION GUIDE STEPS
Remove the hood
electrical compartment
and insert house wiring
through hood wire
clamp.
Rest the back cavity of
the hood on wall
extension metal tabs.
Secure hood to wall
extension using 8
provided no. 10-32 x
1/2" quadrex screws (4
on both sides). See
illustration at right.
Tighten wire clamp.
F
OLLOW HOOD INSTALLATION GUIDE STEPS
AWEPD S
I
NSTRUCTIONS
90°
T
AB
BEFORE INSTALLING HOOD
S
CREW
LOCATIONS
FINALIZE HOOD INSTALLATION
ERIES
4
6
TO
.
9
11
TO
TO
.
Publicité
Sommaire des Matières pour Broan Elite AWEPD Serie
- Page 1 AWEPD S XTENSION ERIES NSTALLATION NSTRUCTIONS Using pliers, unfold to 90° both wall extension metal tabs to HIS KIT CONTAINS align hood during installation. • 1 W ALL EXTENSION • 1 P . S97018867) ARTS BAG SERVICE PART NO INCLUDING WIRE 5/8"...
- Page 2 ’ IRECTIVES D INSTALLATION DE LA RALLONGE DE HOTTE AWEPD DE LA SÉRIE À l’aide d’une pince, déplier les deux languettes de la rallonge ET ENSEMBLE CONTIENT de hotte à 90° afin d’aligner la hotte pendant l’installation. • 1 RALLONGE DE HOTTE •...
- Page 3 NSTRUCCIONES PARA LA INSTALACIÓN DE LA EXTENSIÓN MURAL AWEPD DE SERIE ESTE JUEGO CONTIENE: Con unas pinzas, abra 90° las dos lengüetas metálicas de la • 1 EXTENSIÓN DE PARED extensión para alinear la campana durante la instalación. • 1 BOLSA DE PIEZAS (NO. DE PIEZA DE SERVICIO S97018867) QUE INCLUYE: 1 ABRAZADERA DE CABLES, 8 TORNILLOS NO.
- Page 4 BROAN-NUTONE ONE YEAR LIMITED WARRANTY Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.