Work Smart ECH75137 Instructions De Montage

FAUTEUIL DE DIRECTION EN CUIR RECONSTITUÉ
ÉTAPE 1 ÉTAPE 2
4
3
6
1
2
ÉTAPE 4 ÉTAPE 5
7
10
10
11
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier que les quantités.
ÉTAPE 1 Insérer cinq Roulettes (2) dans la Base (1). Pousser très fort jusqu'à ce que vous entendiez ou sentiez la Roulette (2) s'enclencher. Insérer
le Cylindre Pneumatique (3) dans la Base (1) et glisser les Soufflets (4) sur le Cylindre Pneumatique (3).
ÉTAPE 2 Fixez le Plaque du Siège (5) au Coussin du Siège (6) avec la flèche dirigée vers l'avant du fauteuil à l'aide de quatre Vis Courtes (9). SERREZ
COMPLÈTEMENT TOUTES LES VIS À L'AIDE DE LA CLÉ ALLEN (12). Fixez le levier au Siège (voir schéma en médaillon) comme illustré.
ÉTAPE 3 Fixez le Coussin du Siège sur le Cylindre Pneumatique et appliquer une pression vers le bas. Fixez les bras (8L et 8R) au Coussin du Siège
à l'aide de deux Vis Mince Longue (10) pour chaque Bras. SERREZ COMPLÈTEMENT TOUTES LES VIS À L'AIDE DE LA CLÉ ALLEN (12).
ÉTAPE 4 Fixez le Coussin du Dossier (7) à l'arrière du Coussin du Siège à l'aide de quatre Vis Mince Longue (10). SERREZ COMPLÈTEMENT
TOUTES LES VIS À L'AIDE DE LA CLÉ ALLEN (12).
ÉTAPE 5 Couvrez les trous dans les Bras à l'aide de huit Capuchons en Plastique (11).
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
ECH75137
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
9
9
8R
5
10
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . .5
3. Cylindre Pneumatique . . . . . . . . . . . . .1
11
4. Soufflet . . . . . . . . . . . . . . . . . . . . . . .1
5. Plaque du Siège . . . . . . . . . . . . . . . . .1
6. Coussin du Siège . . . . . . . . . . . . . . . .1
7. Coussin du Dossier . . . . . . . . . . . . . . .1
8. Bras (8L et 8R) . . . . . . . . . . . . . . . . . .2
9. Vis Courte . . . . . . . . . . . . . . . . . . . . .4
10. Vis Mince Longue . . . . . . . . . . . . . . .8
11. Capuchon en Plastique . . . . . . . . . . .8
12. Clé Allen (non montré). . . . . . . . . . . .1
© Office Star Products août, 2023
8L
10
1
QTÉ
WORK SMART LIMITED WARRANTY
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization. At it's
option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on
components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 275 lbs. or less.
The BC9601 is for persons weighing 300 lbs. or less. The BC9602 is for persons weighing 400 lbs. or less. The BC9603 is for persons weighing 500 lbs. or less.
EX1098, EC1283C & ECH12801 are for persons weighing 350 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence,
alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic dam-
age that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from use of this
product. When usage is more than 40 hours per week, a two year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state. All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts.department@officestar.net, by Fax 1-909-930-5629, or
toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 3:30 p.m. Pacific Time.
ECH75137
BONDED LEATHER EXECUTIVE CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat, remove pressure from seat and pull lever (1) up.
To lower seat, sit on chair and pull lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an adjustment that
will allow the user to change the tension of the tilting feature. Turn knob (2)
clockwise to increase tension and counter-clockwise to decrease or ease the
tension. To lock, return chair to the upright position and push lever (1) in. To
unlock, pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
• ARM FLIP UP AND DOWN
To raise arm, simply pull up on arm. To lower arm, simply push down on arm.
WARNING
1. Use this product only one person at a time.
2
2. Do not use this chair unless all bolts screws and knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as head
covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.