Publicité
1U03 2582
Model: EBW-600/660
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any,
that mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
WARNING:
• If the range hood is not installed properly, it could
become detached and fall.
• Ensure that the metal duct does not touch other metal
housing materials, otherwise fire or electric shock could
result.
1
According to the conditions where the range hood is
installed, determine whether it will be discharged
vertically or horizontally (7" round duct). For vertical or
horizontal discharge, run duct work between the hood
location and the roof cap or wall cap.
For best result in either direction, use a minimum
number of transitions and elbows. Be sure to attach a
roof cap or wall cap to avoid rain/wind entry.
Roof cap
7" round duct
(For vertical discharge)
Soffit
7" round duct
(For holizontal
discharge)
Range hood
CAUTION:
• Install the range hood unit on a
wall strong enough to support its
weight. Otherwise, it may
become detached and fall down.
2
Arrange the ends of 7" round duct and wiring conduit
so that they can connect with the top of the range
hood unit.
uct
1-3/16"
EBW-660:18"
EBW-600:15"
Range hood unit
Note: This range hood can directry connect to the
duct without using the supplied exhaust port.
Refer to the steps desclibed under "In case
of direct duct connection" in 2. Range Hood
Mounting.
3
Referring to "DIMENSIONS" above, insert 2 supplied
screws (M5.1×45) into the mounting wall for the left
and right keyholes of the cabinet. Allow about 1/4"
space between the wall and screw-heads for hanging.
Note: Be sure to reinforce the wall with some wood
panel.
1/4"
Wall Wood panel
4
Remove 4 screws.
Front cover
5
Detach the front
cover with pulling
up its bottom side.
Downloaded from
www.Manualslib.com
INSTALLATION MANUAL
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
e) The end user is responsible to ensure compliance
with all Federal, State and Local Environmental
and Fire codes.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Check that the hood is correctly installed, since
incorrect installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
2. Range Hood Mounting
CAUTION:
• Wear working gloves to avoid injury.
In case of using exhaust port
1
Attach the supplied exhaust port on the top of the
range hood with 4 screws.
Exhaust port
2
With inserting the exhaust port to the duct, hook
both the left and right keyholes of the enclosure on
the screws provided "1. Preparation" in step 3.
Wall cap
7" round duct
Wood panel
3
Tighten both the left and right screws, then put 2
supplied screws (M5.1×45) in the holes under the
keyholes and tighten them firmly.
6-15/16"
Tighten
4
Make the duct joint secure and air-tight using non-
flammable tape (not supplied).
Non-flamable tape
Wall stud
In case of direct duct connection
1
Remove 3 screws and loosen 2 screws.Make the
wire free from cord clamp, then disconnect 6P
connector.
Wall
Wood panel
6P connector
Loosen
Cord clamp
Place the range hood on the floor
Pull up
manuals search engine
Range Hood
NAMES OF PARTS
Front cover
Exhaust port
Enclosure
Slot Filter
Lamp
(standard MR16-GU10, 35Watt)
(not supplied)
DIMENSIONS
TOP VIEW
10-5/16"
∅
7/8"
A
B
FRONT VIEW
∅
2-
3/8"
Holes for mounting range hood
17-11/16"
Front panel
BOTTOM VIEW
(Requires a front panel
for a complete unit)
A
B
C
24"
EBW-600
30"
23-5/8"
30"
24"
EBW-660
36"
29-1/2"
30"
INSTALLATION
3. Connecting Power
2
Pull up the top of the fan unit and detach it with
disengaging its bottom U-cut part.
Pull up
WARNING:
• Electrical wiring should be done by a qualified
person(s) in accordance with all applicable codes
and standards, including fire-rated construction. An
unqualified person doing the work could result in fire,
electric shock or injury.
• This range hood uses 120V AC. Do not connect to
other voltage since fire, electric shock or damage
could result.
U-cut
1
Remove the nut (not
supplied) from the conduit
connector at the end of
3
With inserting the duct into the top of the range
power wiring.
hood,hang its keyholes on the screws
provided"1.Preparation" in step 3.
WARNING:
Be sure to switch OFF the power at service panel
before wiring.
Wood panel
2
Remove one
screw fixing the
wire cover and
detach it.
4
Tighten both the left and right screws, then put 2
3
supplied screws (M5.1×45) in the holes under the
Connect the conduit through the connecting hole of
keyholes and tighten them firmly.
the enclosure using the nut previously removed.
Tighten
4
Connect wires tightly and securely using wire
connectors (not supplied).
Connect the electrical wires as follows:
5
Make the duct joint secure and air-tight from inside
using non-flammable tape (not supplied).
Range hood
Non-flammable
tape
Duct
• Black to Black
• White to White
• Green to Green
5
Replace the wire
cover with the screw
6
Engage the bottom U-cut part of the fan unit with
removed previously.
loosened screws.
Make sure that all
wires are connected
properly and
enclosed inside of
the wiring
compartment.
6
Two 35 Watt halogen light bulbs (not supplied) can be
U-cut
mounted in this range hood.
Prior to function check, install light bulbs (Bulb type
standard MR16-GU10), rated 120 V - 35 Watt or below.
The following light bulbs are recommended for this
U-cut
range hood.
• GE Model No. Q35GU10/FL/CD
7
Fix the fan unit using removed 3 screws and
• PHILIPS Model No. Twistline 35W GU10 120V MR16
tightening 2 screws.
Connect 6P connector and fix the wire with the cord
Turn the lamps clock-wise to install.
clamp.
Note: When installing the bulb, be sure to fix to the
6P connector
Tighten
Cord clamp
CIRCUIT DIAGRAM
Lamp Switch
Front panel
Black
(Requires a front panel
for a complete unit)
Motor
Switch
Connector
Connector
White
120V
Black
60Hz
White
Green
Black
Capacitor
ACCESSORIES
(Unit: inch)
• Screw M5.1×45 ........ Four (4) pcs.
• Screw M4×10 ........... Two (2) pcs.
Holes for mounting range hood
RIGHT SIDE VIEW
19"
RANGE HOOD LOCATION
5-15/16"
∅
6-15/16"
1
The range hood must be installed just
above the cooktop.
2
The minimum distance from the cooking
surface to the bottom of the range hood
must be 24".
3
The total weight of the range hood units
are as follows;
EBW-600
46.3 lbs. (21.0kg)
EBW-660
50.7 lbs. (23.0kg)
11-15/16"
*without front panel
4
Power requirements are:
AC120 V, 60 Hz, 2.7 Amp
WARNING:
• Check that the hood is correctly installed, since incorrect installation could
result in the detachment of the range hood and the unit could fall down.
CAUTION:
• To protect hands from injury, wear working gloves when installing the range
hood.
4. Attaching Front Cover and
Supply Wires
Front Panel
1
Insert the upper side of the front cover into the
enclosure as shown, and fix it using 4 screws.
Conduit
(Not supplied)
2
With holding the front panel by both hands, engage
the upper hook of the front panel.
3
Lower the bottom of the front panel slowly with
checking that the front panel has hung on the left and
Nut
right stoppers of the enclosure, then insert both the left
(Not supplied)
and right tabs of the front panel into the slits of the
enclosure.
Note: Be careful not to drop the front panel to avoid
injury.
Stopper
Wire cover
2
3
3
4
Fix the front panel using 2
screws (M4×10) supplied.
Nut
Wire box
5
Attach 2 cover plates (supplied with the front panel) to
Conduit
the left and right of the front panel as illustrated.
(1) Hook the cover plate on the front panel.
(2) Press the cover plate until it is locked.
Wires
Wire connector
(conduit side)
(not supplied)
How to remove the cover plate
While holding the cover plate, slide a flat-head
Wires (unit side)
screwdriver into the gap below.
Note:
Please be careful
not to damage
Wire cover
the cover plate by
the flat-head
screwdriver.
5. Function Check
(1) Turn on the power to the range hood.
(2) Make sure that the switches and light operate
correctly.
Refer to page 4 of the Operation Manual.
socket securely.
(3) Make sure that the range hood functions properly
and it has no abnormal noises and/or vibration.
6. Explanation to the End User
Push the lamp, and
(1) Referring to the Operation Manual, explain the
turn it clock-wise.
operation of this range hood to the end user.
(2) The Installation Manual and Operation Manual should
Lamp (standard MR16-GU10, 35Watt)
be given to the end user.
(not supplied)
Fan Switch
Connector
Pilot Lamp
Connector
White
Black
Grey
Black
Lamp
Yellow
Black
White
White
Black
Black
Connector
White
White
Black
Black
Lamp
Connector
24"(minimum)
Cook top
Enclosure
Front cover
Front cover
Front panel
2
3
Cover plate
2
Lock
Front panel
1
Hook
Cover plate
Cover Plate
Push to turn ON
Publicité
