Publicité
Liens rapides
Publicité
Sommaire des Matières pour Biamp Tesira Server
- Page 1 SERVER SERVER I/O OPERATION MANUAL November 2017 585.0278.90C...
- Page 2 Tesira SERVER and SERVER IO PRODUCT DESCRIPTION The Tesira SERVER is a digital network server. It is factory configured with one DSP-2 card and can accept up to a total of eight DSP-2 cards. The SERVER is also factory configured with one AVB-1 card and has a second slot that can be outfitted with an additional AVB-1 card, a 32 x 32 channel SCM-1 CobraNet card, a 64 x 64 channel DAN-1 Dante™...
- Page 3 Tesira SERVER and SERVER IO FRONT PANEL Tesira SERVER and SERVER IO front panel (identical) 1 – Ventilation fan cover 2 – LED status indicators 3 – Display navigation buttons 4 – OLED display Ventilation fan cover Each device has a perforated cover to allow cool air into the chassis. A variable speed temperature controlled fan allows air into the front of the unit and out of the rear left side.
- Page 4 Tesira SERVER and SERVER IO FRONT PANEL Display Navigation Buttons Capacitive-touch buttons allow navigation through the OLED display menu to view and configure device and networking information, as well as see system-wide faults. Navigating the display is accomplished by touch-sensitive UP and DOWN and SELECT buttons.
- Page 5 Tesira SERVER and SERVER IO FRONT PANEL Network Parameters The network parameters screen shows the following information Host name • IP address • Subnet mask • Gateway • Display Settings The display settings operations include the following: Change brightness and contrast •...
- Page 6 Tesira SERVER and SERVER IO REAR PANEL Tesira SERVER 1. AC Power inlet 2. Serial Port 1 3. Serial Port 2 4. Secondary Ethernet control port (RJ-45) 5. Primary Ethernet control port (RJ-45) 6. GPIO connections 7. Slot 2; always loaded with AVB-1 digital audio networking card for AVB 8.
- Page 7 SIC-4 The Tesira SIC-4 is a modular analog input card for use with Tesira SERVER and SERVER-IO devices. Each SIC-4 provides four channels of mic or line level audio input. The inputs are electrically balanced and provided on plug-in barrier strip connectors.
- Page 8 Tesira SERVER and SERVER IO SPECIFICATIONS Tesira SERVER Specifications (audio specifications given reflect use of SIC-4 and SOC-4) Frequency Response +0/-0.25dB Phantom Power: +48 VDC (20Hz~20kHz @ +4dBu): (7mA/input) THD+N (20Hz~20kHz): Cross Talk (channel to channel @ 1kHz): @ 0dB Gain, +4dBu In <...
- Page 9 To reduce the risk of fire, use only No. 26 AWG solid copper wire for telecom circuit connections. Intended for Installation and Service by Skilled Personnel Only: CAUTION – To reduce the Risk of Electric Shock, Installation and Service of Biamp Products should be conducted only by Skilled Persons who are Biamp Qualified Audio Installation Professionals.
- Page 10 Para la instalación y mantenimiento solo por parte de personal calificado: PRECAUCIÓN – Para reducir el riesgo de descarga eléctrica, la instalación y el mantenimiento de los productos Biamp deben ser realizados por personas calificados que formen parte de los Profesionales capacitados en la instalación de audio de Biamp.
- Page 11 Installation et interventions réservées au personnel compétent: MISE EN GARDE – Pour limiter les risques d’électrocution, l’installation des produits Biamp et les interventions sur ces produits doivent être réalisées uniquement par du personnel compétent faisant partie des professionnels d’installation audio qualifiés de Biamp.
- Page 12 Brandrisiko zu reduzieren. Ausschließlich für Einbau und Wartung durch geschultes Personal vorgesehen: VORSICHT – Zur Verringerung der Stromschlaggefahr sind Einbau und Wartung von Biamp-Geräten ausschließlich durch geschulte Personen, bei denen es sich um von Biamp geschulte Audio-Fachleute handelt, vorzunehmen. Führen Sie keine anderen als die in der Betriebsanleitung angegebenen Wartungsarbeiten aus, vorausgesetzt, Sie wurden hierfür geschult.
- Page 13 警告 – 由市电供电的产品采用了安全接地技术，必须与正确接地的市电插座连接，才能提供接地防护。 断开设备连接 – 市电插头可用于断开 市电电源且必须保持时刻可运行状态。 小心 – 在提供了 POTS 电话接口选项时，必须由训练有素的人员将电话接口与本设备的电信回路进行连接。为减少火灾风险，只能使用 26 号 AWG 实心铜线连接电话端口。 只适用于专业技术人员来执行的安装和服务： 小心 – 为减少电击带来的风险，Biamp 产品的安装和服务应该只能由 Biamp 音频安装专业技术人员来执行。 除非您是专业技术人员，否则不能执行未包含在操作说明中的任何服务。 在打开产品之前，专业人员必须先断开交流市电电源。 小心 – “辅助电源”的安装步骤只适用于专业技术人员，而且必须遵循所有的本地法规。 • 对于美国，国家电气法规 ANSI/NFPA 70。 • 对于加拿大，加拿大电气法规第 1 部 CSA C22.1 第 2-128、12-010(3) 和 12-100 节。...
- Page 14 위험을 줄이기 위해서는 전기 통신 회로 연결은 26번 AWG 솔리드 동선만 이용하십시오. 공인 전문가의 설치 및 서비스: 주의 – 전기 충격의 위험을 줄이기 위해, Biamp 제품의 설치 및 서비스는 Biamp 공인 오디오 설치 전문가에게 의뢰해야 합니다. 전문 인력이 아닌 경우, 작업 지침에 담긴 내용 이외의 사항에 대해 서비스를 제공하면 안됩니다.
- Page 15 .لتمديدات روابط دائرة االتصاالت AWG 26 :هذا الجهاز معد للتركيب والصيانة من قبل الموظفين الماهرين فقط Biamp إال من قبل األشخاص المهرة وهم المهنيون المؤهلون تنبيه - للحد من خطر حدوث صدمة كهربائية، ينبغي أال يتم تركيب وصيانة منتجات .Biamp في...
- Page 16 Destinado para Instalação e Manutenção apenas por Pessoal Qualificado: ATENÇÃO – Para reduzir o risco de choque elétrico, a instalação e a manutenção dos produtos Biamp devem ser realizadas somente por pessoas qualificadas, que são profissionais de instalação de áudio qualificados da Biamp.
- Page 17 одножильный медный провод типа 26 AWG. Предназначено для установки и обслуживания только опытным персоналом ПРЕДОСТЕРЕЖЕНИЕ! Для снижения риска поражения электрическим током установку и обслуживание устройств Biamp должны выполнять только лица, которые являются опытными специалистами по установке аудиосистем Biamp. Не проводите какое-либо обслуживание, помимо указанного в инструкциях по эксплуатации, если вы не обладаете соответствующим опытом и...
- Page 18 This equipment is not user serviceable. If trouble is experienced with this equipment, for repair or warranty information, please contact Biamp Systems Corporation, phone number 503.641.7287. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
- Page 19 RoHS COMPLIANT This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directive 2011/65/EU. An EU RoHS Materials Content Declaration document may be obtained at www.biamp.com (This information is presented to comply with the requirements of Chinese law SJ/T11363-2006) 有害物质表...
- Page 20 Warranty Period Exception Table below, for which there is a different time period specified. The Warranty Period begins (a) the date of the original end user’s purchase from an authorized Biamp Systems dealer or (b) six months after the product is first shipped from Biamp Systems’...