Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
CONTENTS
Hood Protector
Instructions Sheet
Alcohol Wipe
Screwplugs
Large Screws
Large Washers
Rust Inhibitor
IMPORTANT: Read all instructions carefully before
beginning the installation.
hElPful hINT
Ensure to use caution when drilling holes in
underside of hood.
STEP 1
Thoroughly clean and dry the hood prior to installation.
Open the hood and trial fit the Hood Protector centrally
onto hood. Note & mark the slots in the Hood Protector
tag that corresponds to the underside of hood. Remove
the Hood Protector. See FIGURE 1.
STEP 2
At the previously marked tag locations. Carefully drill the
underside of hood using a 3/16" or 5mm drill bit. Do this for
the 4 locations. See FIGURE 2.
FAILURE TO DO THIS MAY RESULT IN PERMANENT
DAMAGE TO THE TOP SIDE OF THE HOOD.
STEP 3
Apply the rust inhibitor to the exposed edges of holes in
hood, as shown. See FIGURE 3.
STEP 4
Insert the white screwplugs provided into the previously
noted vacant holes, as shown. See FIGURE 4.
x1
Abrasive Resistant
x1
Tape
x1
x4
x4
x4
x1
x3
1
2
3
4
3/16" or 5mm
RUST INHIBITOR
SCREWPLUG
SUP279
1/6
K6859752
82209882
Publicité
Sommaire des Matières pour Jeep K6859752
- Page 1 SUP279 K6859752 82209882 CONTENTS Hood Protector Abrasive Resistant Instructions Sheet Tape Alcohol Wipe Screwplugs Large Screws Large Washers Rust Inhibitor IMPORTANT: Read all instructions carefully before beginning the installation. hElPful hINT Ensure to use caution when drilling holes in underside of hood.
- Page 2 SUP279 K6859752 82209882 STEP 5 Re-install Hood Protector onto hood. Ensure that the boss heads of the screwplugs locate into the slots in the Hood Protector tags. Centralize and secure Hood Protector to hood using the large screws and large washers provided.
- Page 3 SUP279 K6859752 82209882 CONTENIDO Hood Protector Cinta Resistente Hoja De Instrucciones x1 Abrasiva Trapo Del Alcohol Enchufes de tornillo Tornillos Grande Arandelas Grande Inhibidor De Moho IMPORTANTE: Lea todas las instrucciones cuidadosamente antes de comenzar la instalación. INDIRECTA PROVEChOSA Asegúrese a la precaución del uso al perforar los agujeros en el superficie inferior de la capilla.
- Page 4 SUP279 K6859752 82209882 PASO 5 Reinstale el protector de la capilla sobre la capilla. Asegúrese de que los jefes del jefe de los screwplugs localicen en las ranuras en las etiquetas del protector de la capilla. Centralice y asegure el protector de la capilla...
- Page 5 SUP279 K6859752 82209882 CONTENTE Hood Protector Bande Résistante Instructions Sheet Abrasive L’alcool Wipe Prises de Vis Grandes Vis Grandes Rondelles Agent Antirouille IMPORTANT : Lisez toutes les instructions soigneusement avant de commencer l’installation. CONSEIl uTIlE. Assurez à l’attention d’utilisation en forant des trous dans le dessous du capot.
- Page 6 SUP279 K6859752 82209882 ÉTAPE 5 Réinstallez le protecteur de capot sur le capot. Assurez- vous que les têtes de patron des screwplugs placent dans les fentes dans les étiquettes de protecteur de capot. Centralisez et fixez le protecteur de capot au capot en utilisant les grandes vis et les grandes rondelles fournies.