Work Smart EMM98958-3 Instructions De Montage

ÉTAPE 1 ÉTAPE 2
4
3
1
8L
2
ÉTAPE 4 ÉTAPE 5
9
7
15
14
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce
indiqués sur la liste et vérifier que les quantités des pièces reçues sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu'à ce que vous
entendiez ou sentiez la roulette (2) s'enclencher. Insérer le vérin pneumatique (3) dans la
base (1) et glisser les soufflets (4) sur le vérin pneumatique (3).
ÉTAPE 2 Fixez les bras (8L et 8R) au coussin du siège (6) utilisant trois vis (10) pour
chaque bras (8). SERRER COMPLÈTEMENT LES VIS À L'AIDE DE LA CLE ALLEN (16).
ÉTAPE 3 Fixez la plaque de siège (5) au coussin de siège (6) avec la flèche dirigée vers l'avant
du fauteuil à l'aide de quatre rondelles plates (12) et quatre vis (9).
SERRER COMPLÈTEMENT LES VIS À L'AIDE DE LA CLE ALLEN (16).
ÉTAPE 4 Fixez le support du dossier (14) au dossier (7) à l'aide de trois vis (9).
SERRER COMPLÈTEMENT LES VIS À L'AIDE DE LA CLE ALLEN (16). Fixez le couvercle en
plastique (15) au dossier (7).
ÉTAPE 5 Fixez le support du dossier (14) à l'arrière de plaque de siège (5) à l'aide de trois
rondelles plate (13) et trois vis (11). SERRER COMPLÈTEMENT LES VIS À L'AIDE DE LA
CLE ALLEN (16).
ÉTAPE 6 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser vers le bas.
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ
COMPLÈTEMENT TOUTES LES VIS.
EMM98958-3
CHAISE A DIRECTION AVEC LE DOSSIER
ET SIÈGE EN MAILLES
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
9
12
10
10
6
5
8R
ÉTAPE 6
11
14
13
PIÈCE
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . . . .5
3. Vérin pneumatique . . . . . . . . . . . . . . . . .1
4. Souflett . . . . . . . . . . . . . . . . . . . . . . . . .1
5. Plaque du siège . . . . . . . . . . . . . . . . . . .1
6. Coussin du siège . . . . . . . . . . . . . . . . . .1
7. Dossier. . . . . . . . . . . . . . . . . . . . . . . . . .1
8. Bras (8L & 8R) . . . . . . . . . . . . . . . . . . . .2
9. Vis (M6 x 20mm) . . . . . . . . . . . . . . . . . .7
10. Vis (M6 x 25mm) . . . . . . . . . . . . . . . . .6
11. Vis (M8 x 20mm) . . . . . . . . . . . . . . . . .3
12. Rondelles plates (M6 x 18 x 1.5) . . . . . .4
13. Rondelles plates (M8 x 18 x 1.5) . . . . . .3
14. Support du dossier . . . . . . . . . . . . . . . .1
15. Couvercle en plastique . . . . . . . . . . . . .1
16. Clé Allen (non montré). . . . . . . . . . . . . .1
© Office Star Products décembre, 2023
6
3
1
3
WORK SMART LIMITED WARRANTY
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
QTÉ
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return
authorization. At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on
components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing
275 lbs. or less. The BC9601 is for persons weighing 300 lbs. or less. The BC9602 is for persons weighing 400 lbs. or less. The BC9603 is for
persons weighing 500 lbs. or less. EX1098, EC1283C & ECH12801 are for persons weighing 350 lbs. or less. This warranty will not cover labor,
freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other event beyond the control
of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential
damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. All Work Smart chairs are built to meet or exceed ANSI BIFMA standards.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or
missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts.department@officestar.net,
by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 3:30 p.m. Pacific Time.
EMM98958-3
MESH SEAT & BACK MANAGER'S CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and pull lever (1) up.To
lower seat height sit on chair and pull lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of the
tilting feature. Turn knob (2) clockwise to increase tension and
counter-clockwise to decrease or ease the tension. To lock
return chair to the upright position and push lever (1) in. To
unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to
move up or down freely. Release the button (3) once the desired
height is reached.
WARNING
2
1. Use this product only one person at a time.
2. Do not use unless all bolts, screws and knobs are securely
ightened.
3. Check that all bolts, screws and knobs are tight every three
months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
6. Do not use as a stepladder.
7. Use this product for its intended purpose only.
8. Use mild detergent only for cleaning.