Publicité
Liens rapides
VM MOBILE STAND
Notice Utilisateur
User Guide
4 A4 Portrait
5 A4 Paysage
2 A3 Portrait + 1 A4 Paysage
4 A4 Portrait
5 A4 Landscape
Version inclinée
2 A3 Portrait + 1 A4 Landscape
Tilted option
L'utilisation de différents formats et différentes orientations d'afficheurs NEW I MAX permet de créer des
combinaisons variées.
Le VM MOBILE STAND peut aussi être assemblé avec la face d'affichage sur sa longueur ou sur sa largeur, en
inclinée ou pas.
The various formats and orientations of the NEW I MAX screens allows varied combinations. The VM MOBILE STAND can be assembled with the display panel
on its' length and his width, tilted or not
Publicité
Sommaire des Matières pour VitrineMedia VM
- Page 1 Le VM MOBILE STAND peut aussi être assemblé avec la face d’affichage sur sa longueur ou sur sa largeur, en inclinée ou pas. The various formats and orientations of the NEW I MAX screens allows varied combinations. The VM MOBILE STAND can be assembled with the display panel on its’ length and his width, tilted or not...
- Page 2 (x1) Cap (x2) Electrical cable with banana plugs (x1) Ref 30403CN005 Ref 30301CN023 Power supply and cord (x1) VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 3 Prepare the two support bars by screwing them 2 by 2 with the threaded rod. Set aside for later. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 4 Positionner verticalement les boules des quatre rotules et les serrer en les vissant à la main. Position the 4 balls of the joint vertically and tighten them by hand. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 5 Slip the first display along the bars and let them rest on the kneecaps. Screw-in the headless screw of the top two bar clamps (screw present on thebar clamp). VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 6 Slip the second display panel along the bar and let it rest on the first panel. Do not tighten the bar clamp. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 7 Visser le troisième et dernier niveau de barres à l’aide des tiges filetées. Install the third and the last level of support bars with the help of the threaded rod. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 8 Elevate the third display panel approximately 10cm along the bar and set it in its position by tightening the headless screw with the two top clamps (screw present on the bar clamp). 10cm VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 9 Slip the last display along the bar. Adjust the height and length of your diplays with the help of the level and by thightenig all the headless screws present on the bar clamp. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 10 Tighten the four joints firmly by hand. Connect the power supply to the column and then to the wall plug. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 11 Prepare the two support bars by screwing them 2 by 2 with the threaded rod. Set aside for later. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 12 Positionner verticalement les boules des quatre rotules et les serrer en les vissant à la main. Position the 4 balls of the joint vertically and tighten them by hand. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 13 Slip the first display along the bar. Screw-in the headless screw using the two top clamps (screw presents on the bar clamp) Use this to set the position to approximately 5cm above of the joints. VitrineMedia VitrineMedia VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 14 Slip the second display screen along the bar and screw-in the headless screw of the top clamps (screw present on the bar clamp) to set the position. VitrineMedia VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 15 Insert one screw into the groove of the joints and tighten them a little at a time on one of the two bars of the column. Repeat the steps with the other joints. Slip the joints on the support bar. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 16 Visser le troisième et dernier niveau de barres à l’aide des tiges filetées. Screw-in the third and the last level of support bars with the help of the threaded rod. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 17 Slip the last display panel along the bar. Adjust your displays with the level and screw-in all the headless screw present on the bar clamp. Visser les deux capuchons. Screw-on the caps. VitrineMedia | 50 route de la Reine - 92 100 Boulogne-Billancourt - FRANCE | Tel: +331 25 36 47 89 | sav@vitrinemedia.com...
- Page 18 Vous trouverez ces informations directement sur le produit ou sur l’emballage. If you need help, you can contact our After Sale Service. Before contacting VitrineMedia, please write down the product model and serial number.