Publicité
Liens rapides
ABBOTT SERIES
Installation Manual / Manuel d'installation
IMPORTANT
Thoroughly inspect your product before proceeding with the installation.
The warranty will be void if the product is installed with a conspicuous defect.
CAUTION
To prevent leaks, silicone must be applied on the outside of the shower.
Read all instructions carefully before starting the installation.
Save this manual for future reference.
IMPORTANT
Inspecter le produit avant de procéderà l'installation.
La garantie sera invalide si le produita été installé avec des défauts apparents.
ATTENTION
Lors de l'installation. l'applicationde silicone doit être à l'extérieurde la douche
Veuiller lire attentivement ce manueld'instruction avant de commencer l'installation.
Conserver ce manuel pour référence ultérieure.
Updated: 2017-05-17
Publicité
Sommaire des Matières pour ACRITEC ABBOTT Série
- Page 1 ABBOTT SERIES Installation Manual / Manuel d’installation IMPORTANT Thoroughly inspect your product before proceeding with the installation. The warranty will be void if the product is installed with a conspicuous defect. CAUTION To prevent leaks, silicone must be applied on the outside of the shower. Read all instructions carefully before starting the installation.
- Page 2 SINGLE THRESHOLD PARTS LIST Cross brace for 72" models only N°/No. Quant./Qty Description Description N°/No. Quant./Qty Capuchon pour montant / Jamb cap Moulure magnétique d’étanchéité / Magnetic Seal Montant mural / Wall Jamb Moulure magnétique/ Magnetic Seal Joint d’étanchéité/ Seal Gasket Poignée / Handle Panneau de verre fixe / Fixed Glass Panel Montant magnétique / Magnetic Seal...
- Page 3 DOUBLE THRESHOLD PARTS LIST SP 10 /No. Quant./Qty Description /No. Quant./Qty Description ° ° SP 1 Butoir de coin / Corner Doorstop SP 6 Joint d’étanchéité / Seal Gasket SP 2 SP 7 Ancrages muraux / Wall Anchors Moulure magnétique d’étanchéité / Magnetic Seal SP 3 Capuchon pour montant / Jamb cap SP 8...
-
Page 4: Tools And Materials Required
I S H F I N TOOLS AND MATERIALS REQUIRED DRILL SCREWS SCREWDRIVER LEVEL PRECISION KNIFE SILICONE DRILL BITS: 1/8", 3/16”, 1/4" MEASURING TAPE SET SQUARE PENCIL MALLET *MASONRY DRILL BIT... - Page 5 48" (45 3/4"~46 3/4") (1159mm~1185mm) 60" (57 1/2"~58 1/2") (1463mm~1489mm) 66" (63 1/2"~64 3/4") (1616mm~1642mm) 72" (69 1/2"~70 3/4") (1768mm~1794mm) 15mm 16mm 16mm Installation du montant mural Wall jamb installation 1/4 ( 6mm)
- Page 6 Commencez par le bas Start at the bottom À l'intérieur de la porte (ø6mm)
- Page 7 10mm 1/8" ENLEVER REMOVE 1/8"...
- Page 8 44mm Intérieur Inside...
- Page 9 1/4" ( Ø6mm)
- Page 10 FOR 72” MODELS ONLY 30" 32" 34" 36"...
- Page 11 FOR 72” MODELS ONLY...
- Page 12 À l intérieur de la porte Inside door...
- Page 13 FOR DOUBLE THRESHOLD INSTALLATIONS 48" (45 1/2"~46") (1155mm~1171mm) 60" (57 1/2"~58") (1459mm~1475mm) 66" (63 1/2"~64") (1612mm~1628mm) 72" (69 1/2"~70") (1764mm~1780mm) 15mm 16mm 16mm 1/4" ( 6mm)
- Page 14 To temporarily hold the glass S 10 To temporarily hold the glass...
- Page 15 SP 1 1/8" ENLEVER REMOVE 1/8"...
- Page 16 FOR 72” MODELS ONLY 30" 32" 34" 36"...
- Page 17 FOR 72” MODELS ONLY...
- Page 18 SP 2 À l'intérieur de la porte On the inside of the shower. SP 3...