FRAM FreshBreeze CF8813A Instructions D'installation

CF8813A
Installation Bulletin:
Bulletin d'installation :
Boletín de Instalación:
Estimated time of installation:
Temps estimé pour l'installation :
Tiempo estimado de instalación:
Acura MDX | Honda Odyssey LX, Odyssey EX,
Application:
Application:
Pilot EX, Pilot LX
Aplicación:
For more application specifics,
please refer to our catalog.
Pour obtenir plus d'information
sur les applications, veuillez
consulter notre catalogue.
Para obtener información
específica sobre la aplicación,
consulte nuestro catálogo.
FRAM Group Operations LLC
Danbury, CT 06810-5109 U.S.A.
©2012 FRAM Group IP LLC
FRAM Group (Canada) Inc.
2430 Meadowpine Blvd.
Unit 105 & 107
Mississauga, ON
L5N 6S2 Canada
SOME VEHICLES MAY DIFFER SLIGHTLY. IF YOU HAVE QUESTIONS
REGARDING THIS FILTER, ITS INSTALLATION OR MORE DETAILS
SPECIFIC TO YOUR VEHICLE, PLEASE VISIT
www.framfreshbreeze.com
FOR HOW-TO VIDEOS AND ADDITIONAL INFORMATION.
CERTAINS VÉHICULES PEUVENT PRÉSENTER DES DIFFÉRENCES. SI VOUS
AVEZ DES QUESTIONS CONCERNANT CE FILTRE, SON INSTALLATION OU
DÉSIREZ OBTENIR PLUS DE DÉTAILS CONCERNANT VOTRE VÉHICULE,
VEUILLEZ VISITER LE www.framfreshbreeze.com POUR OBTENIR
DES DÉMONSTRATIONS VIDÉOS ET PLUS D'INFORMATION.
PUEDE VARIAR UN POCO EN ALGUNOS VEHÍCULOS SI TIENE PREGUNTAS
SOBRE EL FILTRO Y LA INSTALACIÓN O DESEA INFORMACIÓN EN DETALLE
PARA SU VEHÍCULO, VISITE www.framfreshbreeze.com, DONDE
ENCONTRARÁ VIDEOS INSTRUCTIVOS E INFORMACIÓN ADICIONAL.
Importado por:
FRAM Group Operations Mexico City S.A. de C.V. FRAM Group Operations Mexico City S.A. de C.V.
Carretera México-Cuautitlán km 31.5 S/N
Nave 5, Conjunto Industrial Cuautitlán.
Col. Loma Bonita
Cuautitlán, Edo. de México
MEX, C.P. 54800
Tel. 01 800 7154 135
Hecho en China
TOOLS: TOOLS: Phillips-head Screwdriver; 5/16" Nut Driver; TOOLS:
FIRST TIME INSTALLATION: Fine Tooth Saw Blade or a Set of Heavy Duty Wire Cutters
LOCATION OF CABIN FILTER: On the passenger side of the vehicle behind the glove compartment in the air conditioner
07-10
evaporator assembly.
45 minutes or less
REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
45 minutes ou moins
45 minutos máx.
1. Open the passenger side door and remove passenger side step plate by grabbing under it and pulling it up. (Fig 1)
2. Remove passenger side lower kick panel by removing a plastic screw toward the floor board and pulling the panel loose. (Fig 2)
3. Open glove box and remove the stops by gently pushing inward and sliding back towards the rear of the vehicle. (Fig 3)
4. Using the Phillips-head screwdriver, remove the two Phillips-head screws from the hinges at the bottom of the glove box and
remove the glove box. (Fig 4)
5. FIRST TIME INSTALLATION ONLY: Using a fine tooth saw blade or a set of heavy duty wire cutters, cut the plastic cross
bar at each end on the perforations to remove and discard. (Fig 5 & 6) DO NOT CUT THE METAL CROSS BRACE.
6. Remove the two 5/16" bolts and two Phillips-head screws on each side securing the metal cross brace and remove brace by
sliding down. (Fig 7 & 8)
7. Open and remove the cabin filter cover by unlatching the bottom first. (Fig 9)
8. Remove the dirty filter and replace with the new filter making sure the filter is seated to the left. (Fig 10)
9. Position the cabin filter cover back in place and make sure it is secured properly.
10. Reinstall the metal brace and secure it with the screws you removed earlier.
11. Reposition the glove box and reinstall the Phillips-head screws on the bottom and reinstall the stops.
12. Reposition the passenger side kick panel and secure it with the plastic screw.
13. Snap the passenger side step plate back in position.
Fig 3
Fig 7
Fig 1
Fig 2
Fig 4 Fig 5
Fig 8 Fig 9
Fig 6
Fig 10