TEXIBLE Wisbi Home Mode D'emploi page 5

USER MANUAL
1. PACKAGE CONTENTS
The package contents:
•
1x TEXIBLE Wisbi
•
1x TEXIBLE Wisbi
(2,4GHz 802.11b/g/n, WPA/WPA2 PSK)
•
1x Unique QR-Code for
TEXIBLE Wisbi App
2. SCOPE OF APPLICATION AND FUNCTION
TEXIBLE Wisbi is the innovative nursing care product that stands
out for its ability to automatically signal an alarm when moisture,
body fluids or a bed exit are detected.
The sensor textile is used in a wide variety of nursing applications,
such as senior and nursing homes, assisted living and family care.
The necessary basic care, as well as the incontinence care and
the supervision of demented and fall-endangered residents
represents an increased care effort for all persons involved.
TEXIBLE Wisbi offers the right support here. The system allows an
optimal skin climate and minimizes the risk of running away.
3. PUTTING TEXIBLE WISBI INTO OPERATION
The TEXIBLE Wisbi transmitter is equipped with a WLAN module
WPA/WPA2 PSK and is integrated into your home network.
Together with the TEXIBLE Wisbi App on your mobile device you
have your personal call system. Every 20 seconds a measurement
is carried out.
When detecting a wet bed pad or a bed exit, an alarm is sent to
your mobile device via WLAN and an active Internet connection
and you receive an acoustic alarm.
1. DOWNLOAD THE APP:
Download the App „TEXIBLE Wisbi" from the Google Play or
the App Store. Start the App and follow the manual.
2. SCAN THE QR CODE: Scan the QR code on the back of the
TEXIBLE Wisbi transmitter with the TEXIBLE Wisbi App to pair
the transmitter with your app
3. INSERT BATTERIES: Insert three mignon batteries (AA) into
the battery compartment. When the batteries are inserted
correctly, the white LED flashes briefly.
Switch the TEXIBLE Wisbi transmitter on through pressing the
button once.
4. CONNECTION BED PAD: Place the bed pad as the top layer on
–Bed Pad
®
–Transmitter
®
5. WLAN PAIRING WITH WPS : Press the button
6. SENSOR SETTINGS: Configure the settings of the system,
Functional test
TEXIBLE Wisbi must be checked for proper functioning before
each use. Switch on the TEXIBLE Wisbi transmitter. Press the
button
lead to a functional test of the electronics and sends an alarm.
Switching TEXIBLE Wisbi off
Once TEXIBLE Wisbi is switched on it is constantly in standby mode
and measures every 20 seconds.
If the transmitter is not used, it can be switched off by pressing the
button
By pressing the button
on again.
the sheet. White cotton side up, blue side down. Then fasten
the TEXIBLE Wisbi transmitter using the push buttons with the
bed pad.
(See image below)
5 seconds (LED flashes white) and then within 2 minutes press
the WPS button on your WLAN router.
The TEXIBLE Wisbi Sender now automatically connects to your
home network. If the connection is OK, the white LED glow for
3 seconds.
After successful pairing, it can take up to 30 seconds until the
status message in the app is updated.
In the future, the transmitter will automatically connect to
your home network after you turn it off and on again.
Problems connecting? Continue with the manual WLAN setup.
MANUAL WLAN SETUP: If the WLAN pairing with WPS does not
work then use the manual WLAN setup: Press the key
times within 5 seconds (LED flashes red).Open the WLAN
settings on your mobile device and connect to WLAN „Wisbi".
Now enter the information (SSID / WLAN name and Password)
of your home network in the app.
The TEXIBLE Wisbi Sender now automatically connects to your
home network. If the manual connection is OK the red LED
glow continuously for 3 seconds.
Problems connecting? Repeat the manual WLAN setup.
such as the delayed alert when leaving the bed, to suit your
individual care needs.
for 3 seconds until the orange LED flashes. This will
for 3 seconds to preserve the batteries.
again once, the transmitter is switched
4 times within
6