Publicité
Les langues disponibles
Les langues disponibles
CAR HOLDER WITH INDUCTION CHARGER
CHARACTERISTICS
•
Input: 12V/1.67A ; 9V/2A ; 5V/2A
•
Output: 9V/1.67A ; 9V/1.12A ; 9V/0.83A ; 5V/1A
•
Charging power: 15W / 10W / 7,5W / 5W (for iPhone X/8/8+) and 5W
•
Operating temperature: -10 to 60°C
•
Over temperature protection: when charging, if the temperature goes over 60°C, the device will automatically stop charging and the
transmitter light will flash red (one second on/one second off). When the temperature drops to 40°C, the device will automatically
recharge.
•
Overvoltage protection: when the device is operated on a wireless load of 5W, it stops automatically as soon as the input voltage
exceeds 6V; for 10W wireless, the device stops charging when the input is higher than 11V.
•
Support WPC Qi wireless charging protocol.
•
FOD (Foreign Object Detection) function: this security allows the transmitter of the wireless charging system to detect if a foreign
object, such as metal, is on its surface. In this case, the induction charger flashes red and blue, to prompt the user to remove the
object, and thus avoid overheating.
PACKAGING CONTENT
•
A car holder with induction charger
•
A cigarette lighter charger USB x 2 / Quick Charge 3.0
•
A USB-C to USB cable
•
A user manual
Wireless charging indicator
Indicator status:
- Stand by: Flashing blue light
- Charging: Stable blue light
Qualcomm Quick Charge 3.0
- No charging: Red light
2.4 A
WARNING & SAFETY INSTRUCTIONS
•
Do not short circuit.
•
Ensure correct voltage is used as continuous excessive voltage could damage your equipment.
•
Do not try to use this charger with appliance requiring more than the rated output power.
•
Do not attempt to open this unit.
•
Please keep the equipment dry. Rain, humidity and various liquids can contain minerals that will corrode the circuit. If the
equipment is wet, dry the product as soon as possible or use a soft cloth to wipe it off.
•
Do not attempt to charge your device with the exposed battery or broken case, and do not charge any device incompatible with
this product.
•
Do not store this product in a cold place. Otherwise, when the temperature rises to normal temperature, humidity will accumulate
inside and damage the electrical appliance.
•
Do not throw, hit or shake the car holder, rough handling of the equipment will damage the internal circuit board and mechanical
structure.
•
Do not use or store the equipment in dusty or dirty places.
•
Some components of this product are magnetic and metallic materials can be adsorbed on this product. Do not use bank cards,
credit cards or any other magnetic element near the product to avoid losing the stored data due to demagnetization.
Directive 2012 / 19 / EU
Correct disposal of this produt
Electronic waste should not be thrown away with household waste. Please recycle them to your authorized agency and check the recycling advice with the relevant
local authorities.
Make an eco-citizen gesture, recycle this product at the end of its life and think about sorting your waste.
Warranty
Products are guarranteed against any failure from manufacturing defects.
This warranty does not cover normal wear or tear, or damage caused by improper use, keep your invoice stapled to the user manual.
Ref: KO028995
Wireless charging area
Extendable arm
Air vent clamp
Infrared
sensor
Adjustable bottom support for
different phone sizes
PRODUCT USE
STEP 1 : ATTACH THE AIR VENT CLAMP TO THE DEVICE
Connect the air vent clamp to the device; insert the ball
to the nut fisrtly and insert to the bolt on the back of the
device
Tips : Make sure to match the phone coil to the wireless
charging area by adjusting the bottom stand (normally the
wireless receiver is located in the center of the phone).
STEP 2 : USE THE TYPE-C CABLE PACKED IN THE BOX TO
CONNECT THE DEVICE AND THE CAR CHARGER
Button switch for
unlocking
Rotary knob
Type-C input
STEP 4 : WHEN THE SMARTPHONE IS CLOSING TO THE
INFRARED SENSOR, THE ARMS WILL AUTOMATICALLY
UNLOCK, AND AFTER ABOUT 3 SECONDS, THE ARMS
WILL LOCK AGAIN
To avoid any hurt, make sure your fingers are not in the pathway of arms
2020/06V01/MKG
Press the button to unlock the air vent clamp;
Screw the nut in clockwise direction
entry and release to grip the air vent
Screw the nut in anticlockwise
direction to loosen the bottom stand
Screw the nut on clockwise after
finished adjusting the cork base
STEP 3: WHEN PLUG INTO THE CAR CHARGER OR OTHER POWER
SOURCE, THE CAR MOUNT WILL AUTOMATICALLY POWER ON
STEP 5 : PRESS THE POWER BUTTON TO UNLOCK THE ARMS
SRDi - 85430 La Boissière des Landes FRANCE
Publicité
