Publicité
Les langues disponibles
Les langues disponibles
ATMOSLED E SERIES
OUTDOOR LED LIGHTING
Assembly, operation, and maintenance instructions
Contents of the box
Safety instructions
Read the instructions.
Save these instructions.
Heed all warnings.
Installation and maintenance must be carried
out by specialists (electrician certified pursuant
to country standards).
This Class II light does not require grounding.
Ref.685300xxxxxxxx is Class I and needs a
ground connection.
Verify that the mains voltage coincides with the
light's.
Do not use the product in the event there are
any defective electrical or mechanical compo-
nents.
If the flexible cable or cord is damaged, it
should be replaced exclusively by the man-
ufacturer, its tech support, or by a similarly
qualified person so as to avoid any risks.
It does not require interior cleaning. Do not
open the light under any circumstances.
Symbols
Directive 2011/65/EU (RoHS) Free of
hazardous substances.
Class II isolation: Double electric
insulation that does not require
protective grounding.
To identify any terminal that is
intended to be connected to an
external conductor to protect against
electric discharge in case of failure.
Do not alter the light under any circumstances. When repairing or replacing it, always use original spare parts provided by the manufacturer.
The product warranty will be voided in the event of any failure to comply in full or in part with these instructions.
Nº
WEIGHT
REF.
LEDs
(kg)
680300
12
5,9
xxxxxxxx
24
7
681300
xxxxxxxx
36
7,2
682300
xxxxxxxx
683300
48
8,4
xxxxxxxx
72
9,8
685300
xxxxxxxx*
Operating temperature: -30... 40ºC (*685300xxxxxxxx: -35... 35ºC)/
Input volt.: 220-240 V~ / PF>0.95 Optic: PC 5 mm thick/
xxxxxxxx: depends on dimming, color temperature, type of optic, and color.
Assembly parts
a
M8
b
The colors of the cables in the conductor corre-
spond to the following:
BLUE - NEUTRAL
BROWN or BLACK - PHASE
YELLOW/GREEN - GROUND
The manufacturer accepts no liability for
damages caused as a result of improper con-
nections with regard to the above-mentioned
color code set out in the REBT (low voltage
electrotechnical regulation).
Disconnect the light's power to replace the
optics and, where applicable, to replace the
polycarbonate protector in the event of wear
and tear.
Do not loosen the light's seal under any circum-
stances or its watertightness may be compro-
mised.
The light source of this light cannot be re-
placed. When the light source reaches the end
of its life, the entire light must be replaced.
Directive 2012/19/EU (WEEE). Waste
from electrical and electronic
equipment waste.
Output voltage below 60 Vdc.
IK10
IK10 protection against harmful
mechanical impacts.
IP66
IP66 protection against the
penetration of solid foreign objects
and water.
TOTAL POWER
L
L
CONSUMPTION
(mm)
(W)
260
39
340
58
340
78
L
388
108
511
165
opção 1A:
SUPORTE DE PAREDE
Conector THB.391.A2A
Ref. 69000801
+
opção 1B: BRAÇO
Suporte horizontal
Ref. 69000201
M8
opção 1C: BRAÇO
Suporte vertical
Ref. 69000401
c
d
e
Double vertical support
Ref. 69000601
In the event of accidental opening, the joints
of the covers must be replaced to ensure IP64
protection.
The light must be placed so that it will not be
looked at directly at distances less than 3.26 m
for long periods of time.
Assembly systems must be according to the
luminaire weight. They must be able to bear 5
times the weight of the luminaire – including its
own weight in Kg.
IP68
Ref. 69000801
423
Ref. 69000401
395
IP68 protection against the
penetration of solid foreign objects
and water.
Do not look directly at the light for
long periods of time.
The equipment fulfills CE marking
requirements.
Ref. 69000201
L
472
L
Ref. 69000601
703
(mm)
EN
Publicité
