Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
6' X 42" BOARD-ON-BOARD PRIVACY GATE – ASSEMBLY INSTRUCTIONS
42-3/4" W
PREPARATION:
Check local ordinances and regulations before building your fence.
Before construction, contact your local utility companies to mark any
underground cables and pipelines. In addition, it is a good idea to
discuss plans with any neighbors along your proposed fence line.
DIGGING POST HOLES:
Dig post holes 18" to 24" in diameter and 36" to 48" deep
(depending on local ordinance or expected frost depth in winter).
Backfill the holes with 6" of gravel.
The gate can be set up left swing or right swing. Consider swing
direction when determining which post will be your hinge post.
Mix concrete in the hole for the hinge post per the instructions on
the bag. Install the post into the hole and tap the post to the proper
depth. We recommend inserting a piece of 4x4 to support the gate
hinge post. Using a level, ensure post is plumb. Brace the post with
temporary supports as the concrete sets (per the instructions).
Repeat with second hole.
STEP 1
Lay out all four pickets so they face
the same way. Slide each picket into
the next, snapping into place.
©2022 UFP Retail Solutions, LLC. All rights reserved. UFP Retail Solutions is an affiliate of UFP Industries, Inc.
2801 East Beltline NE, Grand Rapids, MI 49525 (844) 529-5882
KIT CONTENTS:
• 2 – Top/Bottom Rails
• 2 – Gate Jambs with covers
ITEMS YOU MAY NEED:
• Drill driver with 1/8" and 1/4" Drill bits
• 7/16" wrench
• Tape measure
• Pencil
Preparation and Digging Post Holes
Assembling and Hanging the Gate
www.ufpi.com
• 4 – Pickets
• Hardware Kit
• Safety glasses
• 4x4 treated wood post
• Blocks or clamp
44" Gate
Opening
Hinge Post
Latch Post
4x4 Wood
Insert
18" to 24" Dia. Hole
Filled with Concrete
Patent-pending technology
Continued on next page.
14247_5/22
36" to 48"
In-Ground
Publicité
Sommaire des Matières pour Outdoor Essentials Bridgeport
- Page 1 6' X 42" BOARD-ON-BOARD PRIVACY GATE – ASSEMBLY INSTRUCTIONS KIT CONTENTS: • 2 – Top/Bottom Rails • 4 – Pickets • 2 – Gate Jambs with covers • Hardware Kit ITEMS YOU MAY NEED: • Drill driver with 1/8" and 1/4" Drill bits •...
- Page 2 6' X 42" BOARD-ON-BOARD PRIVACY GATE – ASSEMBLY INSTRUCTIONS Assembling and Hanging the Gate continued STEP 2 STEP 5 Slide the rails onto the assembled pickets. Align the rails on the gate with the rails on the existing fence. There must be at least a 2"...
- Page 3 BARRIÈRE INTIMITÉ PLANCHE À PLANCHE DE 1,8 M X 106 CM (6 PI X 42 PO) INSTRUCTIONS ET CONSEILS D’ASSEMBLAGE CONTENU DE L’ENSEMBLE : • 2 – Traverses supérieures/ • 4 – Piquets inférieures • Trousse de quincaillerie • 2 – Jambes de barrière avec couvercles ARTICLES DONT VOUS POURRIEZ AVOIR BESOIN : •...
- Page 4 BARRIÈRE INTIMITÉ PLANCHE À PLANCHE DE 1,8 M X 106 CM (6 PI X 42 PO) INSTRUCTIONS ET CONSEILS D’ASSEMBLAGE Assemblage et suspension de la barrière (suite) ÉTAPE 2 ÉTAPE 5 Faites glisser les traverses sur les piquets assemblés. Alignez les traverses de la barrière avec les traverses de la clôture existante. Il doit y avoir un espace d’au moins 5 cm (2 po) entre le sol et la traverse inférieure pour que la barrière fonctionne correctement.
- Page 5 PUERTA DE PRIVACIDAD DE TABLAS ENGANCHADAS DE 6 PIES X 42 PULG. – INSTRUCCIONES DE ARMADO UN KIT INCLUYE: • 2 – Rieles superior/inferior • 4 – Tablas • 2 – Jambas con cubiertas • Juego de herrajes ARTÍCULOS QUE PUEDE NECESITAR: •...
- Page 6 PUERTA DE PRIVACIDAD DE TABLAS ENGANCHADAS DE 6 PIES X 42 PULG. – INSTRUCCIONES DE ARMADO Ensamblado y colocación de la puerta PASO 2 PASO 5 Alinee los rieles de la puerta con los rieles de la cerca existente. Debe Deslice los rieles en las tablas armadas.