Jennair JDAF3924RX Mode D'emploi

PRODUCT MODEL NUMBERS
JDAF3924RX JDAF5924RL
JDAF5924RX
DRAIN REQUIREMENTS
A new drain hose is supplied with your dishwasher. If drain
■
hose is not long enough, use a drain hose extension with a
maximum length of 12 ft (3.7 m).
Make sure to connect drain hose to waste tee or disposer
■
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
IMPORTANT:
This product is not equipped with a high loop on
the side of the dishwasher. The installer is responsible for adding
a high loop in the adjacent cabinet. A high loop is required if
the dishwasher will drain into a floor drain. This prevents water
draw off from the dishwasher during operation. When the drain
is connected to a sink drain, counter-top air-gap or disposer, the
high loop is generally not required. An check valve internal to the
drain prevents back-flow into the dishwasher.
Make sure to use an air gap if the drain hose is connected to
■
house plumbing lower than 20" (508 mm) above subfloor or
floor.
Use of air gap
Air gap
If required, the air gap should be installed in accordance with
■
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
Use 1/2" (13 mm) minimum I.D. drain line fittings.
■
WATER SUPPLY REQUIREMENTS
This dishwasher maybe fitted with a smart inlet hose with a
■
water cut off valve. Do not cut the water inlet hose for any
reason, to install, adapt or shorten.
This dishwasher has a water heating feature and also requires
■
a connection to a hot water supply line.
A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)
■
water pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
■
3/8" (95 mm) O.D. copper tubing with compression fitting or
■
flexible braided water supply line.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
W11589944B
Undercounter Dishwasher
Included water inlet hose with Leak Detection System for some
■
models.
JDAF5924RM
Included 3/8" (9.5 mm) Compression x 3/4" (19 mm) Water inlet
■
adapter (only for models with Leak Detection System).
If installed in new construction, make sure the house water
■
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
ELECTRICAL REQUIREMENTS
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code,
ANSI/NFPA 70 - latest edition, and all local codes and
ordinances.
For a fee, a copy of the above code standards can be obtained
from:
You Must Have:
120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply.
■
Copper wire only.
■
A maximum of 2 field wiring supply conductors (12 AWG
■
largest size) plus 1 grounding conductor are permitted in the
terminal box.
We Recommend:
Install the dishwasher on a circuit with appropriate interrupte
■
per your local code. The dishwasher is compatible with tim
delay fuses, standard circuit breakers, and GFCI and AFCI
circuit breakers.
Circuit Requirement:
The dishwasher may be installed on the same circuit as a
■
garbage disposal providing that the branch circuit cannot
exceed rated circuit load and must comply with all governing
codes and regulations such as but not limited to National
Electrical Code, ANSI/NFPA 70 - latest edition.
No electrical connections other than the dishwasher power
■
and ground connections can be made inside of the dishwasher
junction box.
If Connecting Dishwasher with a Power Cord:
Use UL Listed power cord kit marked for use with
■
dishwasher. See the "Tools and Parts" section at
the front of the Owner's manual for part details and
orders.
Plug into a grounded 3 prong outlet. Outlet must meet
■
all local codes and ordinances.
If Connecting Dishwasher with Direct Wiring:
Use flexible, armored, or nonmetallic sheathed copper
■
wire with grounding wire that meets the
wiring requirements for your home and
local codes and ordinances.
Use only the supplied plastic cable fittings for flexible and
■
non-metallic sheathed wiring (Romex, etc.). Do not use metallic
strain reliefs for these wire constructions.
Use a UL-listed/CSA-approved metallic strain relief for armored
■
cable installations (21 mm diameter), Using the strain relief's
manufacturer installations instructions.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
1