Bell & Ross BR 03-92 diver BROWN BRONZE Notice Technique page 3

BR 03-92 DIVER BROWN BRONZE
LTD 999 PCS
BR-CAL.302
Calibre BR-CAL.302. : mechanical with automatic winding. Power
Movement
reserve approximately 40 hours.
with quickset. Time-setting with hacking function.
directionnal rotating notched bezel.
GENERAL USAGE
To unscrew the crown in position 0, rotate it anticlockwise.
Starting the watch . When the watch has stopped , unscrew the crown out to
position 1 and wind the movement by rotating the crown clockwise. After approx-
imately 40 rotations, the watch is fully wound (the winding mechanism does
not have a stop to prevent overwinding). The power reserve is approximately
A
B
C
D
(x4)
E
STRAP MOUNTING
Attachments (E) with screws on the outer face of the lugs
The 4 socket head screws (hexagon socket/1.3 mm
diameter) mount the strap to the case attachments.
These screws must be handled carefully, using the
2 tools supplied with the watch in its box.
IMPORTANT
As with all mechanical watches with a date function,
*Quickset date setting.
quickset date setting (crown in position 2) MUST NOT UNDER ANY CIRCUM-
STANCES be carried out between the times of 9 P .M. (21:00) and 3 A.M. (03:00).
. Magnetic fields can adversely affect the accuracy of your watch.
Magnetic fields
Also, we would recommend that you avoid placing your watch near electronic
devices that may generate large magnetic fields (radio, smartphone, television,
computer, tablet, loudspeakers etc.).
Water resistance . Once the watch is set, to ensure perfect water resistance,
push the crown back and screw back to position 0.
.
underwater
Note : The 4 slotted screws (D) mount the bezel to the case and ensure the water
resistance of the watch. To benefit from the Bell & Ross warranty, these screws
must never be unscrewed.
: hours, minutes and seconds. Date
Functions
: 42 mm in diameter. Uni-
Case
0 1
H
G
F
Never operate the crown
40 hours when fully wound. When the watch is worn , the automatic mechanism
will wind the movement.
Setting the date
2 and set the date by rotating the crown anticlockwise. Slow setting (crown in
position 3): to ensure the date changes at midnight rather than noon, it is recom-
mended you set the date by adjusting the hands of the watch. Pull the crown out
to position 3 and turn the hands until the date changes. Then set the precise time.
Setting the time
enabling you to set the time to the nearest second. Set the time by rotating the
crown in the required direction.
A. Minute hand
B. Hour hand
C. Second hand
2 3
D. Case attachment screws
E. Strap attachment
F. Unidirectionnal rotating bezel
G. Date
H. Crown
0. Unscrew the crown (rotate anticlockwise)
1.
Wind the movement manually (rotate clockwise)
2. Set the date (rotate anticlockwise)
3. Set the time (rotate in either direction)
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the
watch and strap with fresh water. It is also recommended to have the water resis-
tance of your watch checked every two years. To ensure a service that meets
the brand's exacting standards, any servicing of your watch must be carried out
by the Bell & Ross service centre or a watchmaker approved by Bell & Ross.
Whenever repairs are made during the warranty period, you must present the
Bell & Ross warranty card, duly dated and signed by the retailer at the time the
watch was purchased.
INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated
at the time of purchase by your approved Bell & Ross point of sale, and presented
every time an operation is performed. You can now access the digital version of
this card and all the information relating to your watch by scanning the QR code
or visiting:
www.bellross.com/warranty.
To ensure a service that meets the brand's exacting standards, any servicing of
your watch must be carried out by the Bell & Ross service centre or a watchmaker
approved by Bell & Ross. The warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the
watch (e.g. violent impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer
or after-sales service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and
tear.
3
. Quickset* (crown in position 2): pull the crown out to position
. Pull the crown out to position 3. The seconds hand will stop,
(NEVER UNSCREW)
ENGLISH