Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
ACULUX 4" SQUARE THICK CEILING ADAPTERS
These adapters are for use with Aculux 4" square aperture fixtures using self-flange or drywall ceiling flangeless trims when
ceiling thickness exceeds 7/8".
CTA4SQ/125 is for use with 7/8" thick to 1-1/4" thick ceilings.
CTA4SQ/163 is for use with 1-1/4" thick to 1-5/8" thick ceilings.
CTA4SQ/200 is for use with 1-5/8" thick to 2" thick ceilings.
Note: Aculux housings require vertical adjustment of the aiming mechanism to ensure maximum performance at various ceiling
thicknesses. The aiming mechanism can be set for 1/2" thru 1-1/2" ceiling thicknesses with 1/8" increments before or after
housing installation.
To adjust (refer to Fig. 1):
1. Loosen thumb nuts (A) on both sides of the aiming mechanism.
2. Flex left and right trim retainer/height adjustment brackets (B)
inward to disengage aiming mechanism.
3. Raise or lower aiming mechanism until indicators point to the
corresponding ceiling thickness (C). If ceiling thickness is
unknown, measure from housing to ceiling surface (D) and
subtract 3/16" from this measurement. Set aiming mechanism
height at this value.
4. Allow trim retainer/height adjustment brackets to flex back
towards original position, locking height.
5. Tighten thumb nuts loosened in step 1.
Trim Spring Height Adjustment
In some applications, trim spring height adjustment is required.
If ceiling thickness is 1-1/4" to 2", one spacer per trim spring is
required. (Spacers are shipped with thick ceiling adapters)
To install (refer to figure 2):
Remove and discard screws holding trim spring assemblies in
place. Install spacers and trim spring assemblies as shown with
provided hardware.
Product Services Phone (888) 387-2212
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/aculux
©2018 Acuity Brands Lighting, Inc.
INSTALLATION INSTRUCTIONS
Figure 1
Figure 2
Rev 06/18
P5519
SPRING ASSEMBLY
SPACER
1 of 2
Publicité
Sommaire des Matières pour Aculux CTA4SQ/125
- Page 1 INSTALLATION INSTRUCTIONS ACULUX 4" SQUARE THICK CEILING ADAPTERS These adapters are for use with Aculux 4" square aperture fixtures using self-flange or drywall ceiling flangeless trims when ceiling thickness exceeds 7/8". CTA4SQ/125 is for use with 7/8" thick to 1-1/4" thick ceilings.
- Page 2 Keep fingers and hands clear of these springs to prevent injury when removing. Product Services Phone (888) 387-2212 1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/aculux ©2018 Acuity Brands Lighting, Inc. Rev 06/18...
- Page 3 ADAPTADORES CUADRADOS ACULUX DE 4" PARA TECHOS GRUESOS Estos adaptadores son para usarse con accesorios Aculux de 4" de abertura cuadrada usando bordes con auto-pestaña o de montaje a ras para tablayeso cuando el grosor del techo es mayor a 7/8".
- Page 4 Mantenga los dedos y las manos alejadas de estos resortes para evitar lesiones al retirarlos. Teléfono de Servicios de Producto (888) 387-2212 1300 S. Wolf Road • Des Plaines, IL 60018 • Teléfono 800-323-5068 • Visítenos en www.acuitybrands.com/aculux ©2018 Acuity Brands Lighting, Inc. Rev 06/18...
- Page 5 ADAPTATEURS DE 4 PO CARRÉS ACULUX POUR PLAFONDS ÉPAIS Ces adaptateurs doivent être utilisés avec les luminaires à ouverture carrée Aculux de 4 po utilisant des garnitures incorporées ou affleurantes pour plafonds en placoplâtre quand l'épaisseur de plafond dépasse 22,2 mm (7/8 po).
- Page 6 Maintenez les doigts et les mains à l'écart de ces ressorts pour éviter toute blessure lors du démontage. Téléphone Services des produits (888) 387-2212 1300 S. Wolf Road • Des Plaines, IL 60018 • Téléphone 800-323-5068 • Visitez www.acuitybrands.com/aculux ©2018 Acuity Brands Lighting, Inc. Rev 06/18...