Publicité
Liens rapides
INSTALLATION INSTRUCTIONS
PURE LED STROBE LIGHT KIT
#900602 & #900604
Please note: You must follow these instructions to install the parts correctly otherwise damage may occur.
Read all instructions before installation and check to see if all parts listed are included.
KIT CONTENTS
Item#
Qty Description
1
8
LED Strobe Light
2
2
Key fob (controller)
3
1
Control module
4
1
Control switch
5
1
Hardware kit (with tape)
1
Pre‐installation preparation.
Verify the kit contents (check against parts listing). Remove any
protective wrapping from the light kit.
2
Align Strobe Lights and Control Module.
Determine the location where you want to mount the control
module (usually under the vehicle's front dash). Lay out the
Strobe Lights under the vehicle so they are evenly spaced. Make
sure each light's wire can reach the control module.
3
Install Strobe Lights and run wiring inside vehicle
to Control Module.
Attach the Strobe Lights to the underside of the vehicle (running
board or rocker panel) with pre‐applied tape. Run wires to the
inside of the vehicle through the firewall or floor boards. Make
sure the wires are not near any moving parts or the vehicle
exhaust. Plug Strobe Lights into the Control Module.
LIMITED WARRANTY
Putco guarantees its products against defects in workmanship and material for as long as you own your vehicle. All painted products have a 90 day warranty on the painted
surface. Any defects resulting from faulty material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor costs.
Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco. Putco is not liable for any vehicle damage resulting from
the installation of our Pure LED Strobe Light Kits.
PUTCO PURE LED STROBE LIGHT KIT (PLASTIC BASE) 2007‐12‐04
BOLT KIT CONTENTS
LED STROBE LIGHT WIRING AND INSTALLATION
Questions? Call Putco's customer service at 1-800-247-3974
Monday – Friday, 8am – 5pm central time
216 West First Street ▪ Story City, IA ▪ 50248
None
4
Find power source and attach to Control Module.
Use the Volt Meter to locate a constantly powered wire (under
the vehicle's dash). Splice power cables for the Control Module to
the powered wire and a grounded wire. Test wiring connections
by turning on the Control Module (Control Switch will illuminate
when properly wired).
5
Mount and install Control Switch inside vehicle.
Locate and mark desired position for Control Switch installation.
Drill a small hole for and mount the switch in the hole. Note: Most
installers prefer to mount the Control Switch on the front dash
within reach of the driver.
6
Permanently install Control Module and
complete installation.
Attach the Control Module to the desired location with two
supplied screws and tape. Re‐test installation and ensure all lights
are working by using the main Control Switch and the remote key
fobs.
www.putco.com
RECOMMENDED TOOLS
Safety Tools
1. Eye Protection
Special Tools
1. Electrical & masking tape
2. Volt meter
Installation Tools
1. Screwdriver (Phillips & Flathead)
2. Pliers
3. Wire cutter
4. Power drill (and drill bits)
www.putco.com
Publicité
Sommaire des Matières pour PUTCO PURE
- Page 1 Attach the Control Module to the desired location with two exhaust. Plug Strobe Lights into the Control Module. supplied screws and tape. Re‐test installation and ensure all lights are working by using the main Control Switch and the remote key fobs. Questions? Call Putco's customer service at 1-800-247-3974 Monday – Friday, 8am – 5pm central time 216 West First Street ▪ Story City, IA ▪ 50248 www.putco.com LIMITED WARRANTY Putco guarantees its products against defects in workmanship and material for as long as you own your vehicle. All painted products have a 90 day warranty on the painted surface. Any defects resulting from faulty material or workmanship will be warranted by Putco and repaired or replaced at our discretion. Putco assumes no extra labor costs. Damages caused by freight carriers, improper installation, misuse, collision, or neglect will not be warranted by Putco. Putco is not liable for any vehicle damage resulting from the installation of our Pure LED Strobe Light Kits. ...
- Page 2 La source de pouvoir de découverte et attache Controlar Módulo. pour Contrôler le Module. Utilice el Metro del Voltio para localizar un alambre constante‐ mente accionado (bajo el arranque de vehículo). Empalme ca‐ Utiliser le Mètre de Volt pour localiser un a alimenté constam‐ bles de energía eléctrica para el Módulo del Control al alambre ment le fil (sous le véhicule précipiter). Episser des cordons d'ali‐ accionado y un molió alambre. La prueba que alambra las conex‐ mentation pour le Module de Contrôle à l'a alimenté le fil et un iones prendiendo el Módulo del Control (Interruptor de Control fil fondé. Essayer les connexions d'installation éléctrique par iluminará cuando alambró apropiadamente). allume le Module de Contrôle (le Commutateur de Contrôle illu‐ minera quand convenablement télégraphié). El monte e instala Interruptor de Control ve‐ Le mont et installe le Commutateur de Contrôle hículo interior. véhicule d'intérieur. Localice y marque la posición deseada para la instalación de In‐ terruptor de Control. Taladre un pequeño hoyo para y monte el Localiser et marquer la position désirée pour l'installation de interruptor en el hoyo. Commutateur de Contrôle. Entraîner un petit trou pour et mon‐ ter le commutateur dans le trou. Instale permanentemente Módulo de Control y D'une façon permanente installer le Module de Complete la instalación. Contrôle et compléter l'installation. Conecte el Módulo del Control a la ubicación deseada con dos Los tornillossuministrados y graba. Reexamine la instalación y Attacher le Module de Contrôle à l'emplacement désiré avec asegure que todas luces trabajen utilizando el Interruptor princi‐ deux les visfournies et enregistre. Tester à nouveau l'installation pal del Control y el remoto clave lbre a bordo. et assure que toutes lumières travaillent en utilisant le Commu‐ tateur de Contrôle principal et les goussets clés éloignés. PUTCO PURE LED STROBE LIGHT KIT (PLASTIC BASE) 2007‐12‐04 www.putco.com ...