American Lighting SFX-5CCT Serie Instructions D'installation

120V SLIM FIT 5CCT FLUSH MOUNT
INSTALLATION INSTRUCTIONS
SFX-5CCT Series
WARNING
These products may represent a possible shock or
fire hazard if improperly installed or attached in any
way. Products should be installed in accordance
with these instructions, current electrical codes,
and/or the current National Electric Code (NEC).
WARNING
The electrical rating of this product is 120V AC,
60Hz. The installer must determine whether the
power supply is appropriate at the luminaire prior
to installation. To avoid possible electric shock, be
sure that power source is turned off at fuse box
and/or circuit breaker prior to attempting
installation or servicing of the fixture.
WARNING
Use with a pancake or standard depth 4" junction
box only. Required distance between mounting
holes: 3-1/2". Do not attempt to alter for other sizes
or purposes.
FIXTURE CONTENTS (SEE FIGURE 1):
Each Slim Fit light includes:
Attached 7" lead wires
Attached Selectable CCT Switch
INSTALLATION:
1. Ensure power is disconnected at the source and any wall switches
are in the "off" position.
2. Attach mounting plate to the outlet box by fastening supplied 1½"
outlet box screws through mounting plate keyholes. (Fig.1)
3. Connect supply wires to fixture wires and insulate with proper size
wire nuts (Fig. 1).
a.) Connect incoming ground wire (green or bare) to fixture
ground wire (green or bare).
b.) Connect incoming common (white) wire to fixture
common (white).
c.) Connect incoming hot (typically black) wire to fixture black wire.
4. Align spring clips on the disk light to hinge on the mounting plate.
Tuck all wires into the outlet box and push up to lock fixture in
place (Fig. 2)
5. Make sure the disk Light is flush to the ceiling. For Wet Location
installation, seal the luminaire to the surface around the entire
edge of the fixture using a weatherproof sealant (Fig. 3)
©2024 American Lighting, Inc. REV2404 www.AmericanLighting.com
SAFETY INFORMATION
• Read all instructions before beginning; Save these instructions for future use.
• To reduce the risk of fire, electric shock, or injury to persons, pay close attention
to this manual and stay within its guidelines when using this product.
• LED Flush Mount light installation requires knowledge of recessed lighting
luminaires and their electrical systems. If not qualified or uncertain, do not attempt
installation: contact a qualified electrician.
• Supply conductors (power wiring) connecting the fixture must be rated for a
minimum of 90°C.
• WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges
of sheet metal or other sharp objects.
• Do not make or alter any open holes in wiring enclosures, nor in any electrical
components during kit installation.
• Do not alter, relocate, or remove wiring, lamp holders, power supply, or any other
electrical component.
• This fixture is suitable for use in dry, damp, or wet locations.
• Do not use these products in luminaires located where elevated ambient
temperatures exist.
• To avoid electrical shock, do not turn on fixture with missing or damaged lens.
• There are no serviceable parts inside the fixture or LED module.
• This fixture is suitable for use in dimming circuits: TRIAC/CL/ELV
• This device is not intend for use with emergency exits or not for emergency lighting.
THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE
THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR
AUTHORITIES HAVING JURISDICTION.
Mounting Plate
(3) Quick Connectors
(2) Mounting Screws
Page 1 of 4
FIGURE 1
Junction
Box
Quick
Connectors
FIGURE 2
Mounting Plate
Spring
Clip
11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633
Mounting
Plate
Keyholes
Mounting Screw
Ground Wire
FIGURE 3
Seal luminaire to surface around
this entire edge.