Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V
25 (7.6)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More
not
Than
More
Than
0
6
18
6
10
18
10
12
16
12
16
14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
Intended Use
This edger is intended for household use.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
4
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16
16
16
14
16
14
12
Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
ASSEMBLY AND ADJUSTMENTS
WARNING:
serious personal injury, turn unit off and
disconnect it from power source before making
any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
DANGER:
come to complete stop.
Assembling the Handle Tubes (Fig. C, D)
1. Remove knobs
handle tube mounting holes.
14
2. Remove tape which secures internal jacketed cable
12
to tubes.
12
3. Slide middle tube
handle tubes together with the knob and curved head
bolt. Note that when you first insert the bolt it may
be necessary to wiggle it carefully to get it past the
jacketed cable inside the tube. There are two positions
available for adjustment to your preferred height
setting. See Figure G for upper handle orientation.
Ensure the cable moves smoothly into the handle tubes
while assembling.
4. Push jacketed cable down into lower tube to remove
the slack. Slide the middle tube into the lower by
locating the groove and the bump. Fasten handle tubes
together with the remaining knob and curved head
bolt. Note that when you first insert the bolt it may
be necessary to wiggle it carefully to get it past the
jacketed wire inside the tube.
CAUTION:
move jacketed wires out of the way.
Fig.C
Fig. D
To reduce the risk of
UNPLUG TOOL. Wait for blade to
2
and curved head bolts
4
into upper tube
3
and fasten
NEVER use a sharp object to
13
from
13
2
Publicité
Table des Matières
