Publicité
Notes
During Assembly
Use
a
soft platform below the parts to avoid scratches and damages.
Product dimensions
can be
adjusted to your specific
needs:
1.The
wall-mounting profile (top-back)
can be
adjusted from 260
to
305 cm
(102.4"
to
120")
above ground.
The
adjusting
is
done when measuring and drilling (Step
12).
Please
note the installation recommendations' height suggested
in
Diagram
A.
It
is
possible to fix the
Patio Cover back
wall
height
at the lowest
point of 260 cm/102.4".
This
method
is
optional
if the
assembly conditions and exterior walls do not allow to
follow
the suggested installation
as
appears
in
the manual.
Please
note
that
the product appearance
may
slightly change
as
a
result,
however snow load
weight
does
not
change.
2. Poles
distance from the wall
can be
adjusted from 310
to
370 cm (122"
to
145.6")
as
suggested
in
Diagram
B1.
Poles
distance from the
side edges can be
adjusted from
0
to
54 cm
(0"
to
21.3")
as
suggested
in
Diagram
B2.
The
adjusting
is
done after assembly and before anchoring (Step 33)
by
sliding
poles and
profile 7040 +7041 at the roof
profiles'
channels.
3. Wall
mounting
and distance from the wall
determine the roof angle and the total depth of the product
(distance
of gutter
from the wall). Higher wall mounting and shorter distance between wall and poles
increase
the roof angle and shorten the
total depth
as
suggested
in
Diagram
C.
During Assembly
IIIIIIIII111111111111111111111111111111111111111111111111111111111111111111111
Steps/pages marked
with
dashed
outline
are
referring to the extension kit
assembly.(steps
4,
7,10,18,30,34)
ir
These steps are
referring
to the installation of the extension kit
on the
right
side
of
the patio
cover;
installation on the left
side
is
possible according
to
same steps.
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Steps
In
case
that
you already own Palram Patio cover it
is
necessary
to dismantle some parts and keep them for future
use.
Step
4:
Insert
15
cm
(6")
of
prosthesis (7506)
to profile 7507,
set
the
screws
as
shown
in
diagram
a,
and insert into profile
7040
/
7041.
Step
9, 10: Please
apply silicone
sealants to the inner and
outer
edges
of
parts
7043
+
7042
as
well
as
to the middle of parts 8119
+
7039
in
order to prevent water from seeping
in.
Step 11: Apply silicone
sealants on
the inner part
of 8116 & 8117
and
connect to the profile.
Step 20:
Please
apply silicone
sealants above beam
7288
+
7290,
in
order to prevent water from seeping
in.
Step
26: Make sure
that the angle between the
back wall
profile
and the panel
supporting
profiles
is
90 degrees. Assembly
of the
panels should start from the middle
of
the patio cover to
each side
alternately.
Step
33:
Please
adjust the
poles (inside
out
and sideways) by sliding
them to their final position prior to anchoring.
Make sure
that
the poles distance from the
Patio cover side edge does
not
exceed 54
cm/21.3".
Step
34:
Please
make sure
that
distance from the poles and the kit connection to original patio cover not exceeds 60 cm.
Please
note:
Anchoring this product to the ground
is
essential to its
stability
and
rigidity.
It
is
required to complete
this stage (Step
35)
in
order for your warranty to
be
valid.
*Tighten
all
screws
when completing
assembly.
Note:
The
wall anchoring kit supplied with this product
is
suitable only for concrete
walls.
Other wall types
need
an
accordant wall fixation
kit.
260-305cm
102.4"-120"
.
.
I
.
-
13°
+
17°
`..
+
-
f
i
-41-
Publicité
