Publicité
Les langues disponibles
Les langues disponibles
IN S T A LLA TION M A NU A L
9. Appliance-specific information
•
The appliance-specific instructions as described in this section prevail over the instructions in the other
!CAUTION
sections! If in doubt follow the instructions in section 9 or contact your supplier.
•
The appliance-specific information as described in paragraphs 9.1 to 9.5 applies to all models described in
this manual. Supplementary installation instructions (per appliance) are described in paragraph 9.6.
9.1 Smoke control area United Kingdom
The DG Instyle corner slim have been recommended as suitable for use in smoke controle areas when burning
wood.In smoke controle areas in the Uited Kngdom the air slide valve may not be closed too far because of
emission laws.The DG instyle corner slim must be fitted with a permanent stop to prevent closure of the
combustion air contoller beyond 240 mm from left side of the stove. A limiting screw is accordingly supplied with
all applainces.This is supplied as a kit in the combustion chamber .This screw is therefore only used in the smoke
controle areas in the Uited Kingdom.In other countries this screw can be disposed of in the appropriate way.With
the installation of an applaince in the United Kingdom:
Ø
Install the screw as shown in Appendix2,fig.13.After fitting,the airslide valve cannot be slid further shut
than legally allowed.
9.2 Convection connection and connection of the flue
9.2.1 Convection air connection
This appliance is provided with removable convection plates that have to be broken out when creating chimney
breast ventilation. The openings that are created in this way can be used to make a connection for convection air.
Here, hot convection air (outflow) is taken to a ventilation opening in the chimney breast. No extra provisions are
required for the inflow of cold convection air. The accessories needed for the outflow are available through your
supplier.
Various options are available for creating a convection air connection. Select the situation that applies to you and
proceed as follows:
New situation (hollow chimney breast made of non combustible material):
Option1:
Ø
Using a hammer, break out the plates for the convection air connection at the top of the appliance
(see appendix 2, fig. 2a).
Ø
Place the rings on the convection openings (see appendix 2, fig. 2b).
Ø
Slide a heat-resistant, flexible hose (Ø 125 mm) over the ring and fasten it with a hose clip or a self-tapping screw.
Ø
Connect the flexible hose to a ventilation element in the top of the chimney breast (at least 30 cm below the
ceiling). These accessories are available through your supplier.
Option 2:
Ø
Using a hammer, break out the 2 convection openings at the top of the appliance (see appendix 2, fig. 2a).
Ø
Place 2 ventilation elements in the top section of the chimney breast (at least 30 cm below the ceiling).
Option 3:
Ø
Do not break out the plates for the convection air connection.
Ø
Place 2 ventilation elements below the appliance to supply relatively cold air.
Ø
Place 2 ventilation elements above the fire (at least 30 cm below the ceiling).
This option is not available in combination with a construction frame.
!Caution
Existing situation or conversion without a hollow chimney breast
Ø
Do not break out the plates for the convection air connection.
Ø
The convection breast of the fire will provide sufficient convection flow.
9.2.2 Connection of the flue
9.2.2.1 Regular connection of the flue
In an existing situation the flue can be connected in 3 ways: without venting material, using a fixed connection or
by using a flexible connection.
Not all connection methods are allowed in all countries! Install the appliance strictly according to the
!CAUTION
country-specific conditions.
For the method without venting material you must create an airtight connection with ceramic wool between
the top side of the fire and the chimney (see paragraph 5.7.2).
37
Publicité
