Kenwood KAC-PS541 Mode D'emploi page 5

Amplificateur de puissance 4/3/2 canaux

Masquer les pouces Voir aussi pour KAC-PS541:

Mode d'emploi (9 pages)

page de 29

/ 29
Signets

Les langues disponibles

Controls

This is a 4 channel amplifier including 2 stereo amplifiers in a body. One

amplifier is referred to as amplifier A and the other is amplifier B. This unit

is compatible with a large variety of systems by combining the switches and

functions described in the following.

1 Fuse (30 A × 2)

2 Battery terminal

3 Ground terminal

4 Power control terminal

Controls the unit ON/OFF.

NOTE

Controls the unit power. Be sure to connect it with all the systems.

5 Speaker output terminals (A.ch/B.ch)

• Stereo Connections:

When you wish to use the unit as a stereo amplifier, stereo connections are

used.

The speakers to be connected should have an impedance of 2Ω or greater.

When multiple speakers are to be connected, ensure that the combined

impedance is 2Ω or greater for each channel.

• Bridged Connections:

When you wish to use the unit as a high-output monaural amplifier,

bridged connections are used. (Make connections to the LEFT channel 9

and the RIGHT channel · SPEAKER OUTPUT terminals.)

The speakers to be connected should have an impedance of 4Ω or greater.

When multiple speakers are to be connected, ensure that the combined

impedance is 4Ω or greater.

2CAUTION

The rated input of the speakers should be no less than the maximum output

of the amplifier. Otherwise malfunction may result.

6 RCA cable ground lead terminal

When using an RCA cable with a ground lead attached, connect the ground

lead to this terminal.

7 ID NUMBER switch

Sets an amp identification number (ID) to be used for amplifier control from

the Center Unit.

Assign ID Number "0" to an amplifier when you use it as the Master amplifier.

Assign ID Numbers "1" to "7" to amplifiers when you use them as Slave

amplifiers. Do not duplicate these numbers.

NOTE

After you have changed ID numbers of amplifiers, turn Off the POWER switch

of the Center Unit and turn it On again.

8 TO H/U terminal

After you have set the Master amplifier, connect it to the Center Unit.

9 REMOTE terminals

Used to connect to Slave amplifiers.

0 RESET button

Resets the microprocessor of the unit.

NOTE

The values you have set with the Amplifier Control are NOT reset.

! LINE IN terminal (A.ch/B.ch)

@ LINE OUT terminal

These jacks output respectively the signals input to amplifiers A and B.

They always output the stereo signals regardless of the position of the

OPERATION switch.

��

�

��

�

��

�

��

�

# Power indicator

Lights when the POWER switch is turned On.

The indicator flashes several seconds when the POWER switch is turned On

or when the Protection function is activated.

$ HPF FREQUENCY control (A.ch/B.ch)

A: Sets the cutoff frequency when the "HPF" switch is set to "ON".

B: Sets the cutoff frequency when the "FILTER" switch is set to "HPF".

% LPF FREQUENCY control (B.ch)

Sets the cutoff frequency when the "FILTER" switch is set to "LPF".

��

^ FILTER switch (B.ch)

��

This switch allows to apply high-pass or low-pass filtering to the speaker

��

�

outputs.

�

��

• HPF (High-Pass Filter) position:

��

The filter outputs the band of higher frequencies than the frequency set

with the "HPF FREQUENCY" control.

• OFF position:

The entire bandwidth is output without filtering.

• LPF (Low-Pass Filter) position:

The filter outputs the band of lower frequencies than the frequency set

with the "LPF FREQUENCY" control.

The speaker output is automatically switched to monaural (L+R).

& AMP CONT (amplifier control) switch (B.ch)

Used to bypass the circuit when you do not control the sound with the

Amplifier Control.

• ON position:

You can control the sound of amplifier B using the Amplifier Control.

• OFF position:

Bypasses the Amplifier Control circuit.

NOTE

Amplifier control is possible even while OFF.

* ISF (infrasonic filter) switch (B.ch)

When this switch is "ON", the frequencies which are below the audible

range and therefore inaudible are cut off so that the quality of the audible

frequencies can be improved.

( OPERATION switch (A.ch/B.ch)

The amplification methods of the signals input to amplifiers A and B can be

selected independently according to the setting of this switch.

• STEREO position:

The amplifier can be used as a stereo amplifier.

• MONO (Lch) position:

Amplifies the signal input from the left side only. Set to this position and

make bridged connections to use as a high-power monaural amplifier. (The

input right signal is not output.)

) HPF (High-Pass Filter) switch (A.ch)

This switch allows to apply high-pass filtering to the speaker outputs.

• ON position:

The filter outputs the band of higher frequencies than the frequency set

with the "HPF FREQUENCY" control.

• OFF position:

The entire bandwidth is output without filtering.

INPUT SENSITIVITY control (A.ch/B.ch)

Set this control according to the pre-output level of the center unit

connected with this unit.

NOTE

For the pre-output level, refer to the "Specifications" in the instruction manual

of the center unit.

��

�

��

�

��

�

��

�

��

� ��

��

�

��

�

��

�

��

�

��

� ��

��

English

Produits Connexes pour Kenwood KAC-PS541

Ce manuel est également adapté pour:

Kac-x541

Kenwood KAC-PS541 Mode D'emploi page 5

Les langues disponibles

Manuels Connexes pour Kenwood KAC-PS541

Produits Connexes pour Kenwood KAC-PS541

Ce manuel est également adapté pour: