Publicité
Note:
Before beginning the installation, make sure all power is off,
shutting power off in breaker box to areas where downlights are to be
installed is recommended.
Required Tools (not included): Safety glasses and gloves.
1.
Double check and measure the ceiling hole. Make sure it is the correct size
for outside rim of the luminaire to cover the hole while still allowing the back of
luminaire to sink in to the ceiling and springs to hold fi rmly.
Remove existing retrofi t can if present or move it out of the way since it will
not be needed for installation.
If new hole is to be cut, use provided hole template. Place
template over the desired location. Trace the outer ring with a pen or pencil (not
included). Cut the opening with a saw (not included). (Figure 1)
Figure 1 / Figura 1 / Schéma 1
2.
Open the cover of the remote driver box. Push and remove one of the
knockouts on the side plate.
Locate power supply leads from remote driver box and connect to power
source using wago connectors (provided).
Connect black wire to live wire, white wire to neutral wire, and green wire
with ground (as shown) and secure using wago connector. Close the cover of
the box. (Figure 2)
ACCESS
NEUTRAL WIRE
(FROM POWER SUPPLY)
GROUND WIRE
(FROM POWER SUPPLY)
LIVE WIRE
(FROM POWER SUPPLY)
Figure 2 / Figura 2 / Schéma 2
3.
Connect the remote driver box to the light fi xture and tighten the nut con-
nector by hand. Arrow on the male and female parts of the connector between
the driver and fi xture cable should match. (Figure 3)
4.
Use switch on the driver box (CCT option need to be selected before fi xture
installation) to select appropriate light color (27K-30K-35K-40K-50K option).
(Figure 4)
Figure 4 / Figura 4 / Schéma 4
STEP-BY-STEP GUIDE
(FROM DRIVER BOX)
GROUND
WIRE
NEUTRAL
LIVE
(BARE COPPER /
WIRE
WIRE
GREEN)
(WHITE)
(BLACK)
(FROM POWER SUPPLY)
NEUTRAL WIRE
connector
GROUND WIRE
connector
LIVE WIRE
connector
Figure 3 /
Figura 3 /
THREAD
Schéma 3
LOCK
5. Place remote driver box thru the cut-out hole.
MUST follow local electric
MUST follow local electric code
placement of the remote driver box. (Figure 5)
Optional Mounting Kits: Instruction sheet for new construction
plate and joist bar kit can be found at www.acuitybrands.com
SIDE WALL
ATTACH USING PROVIDED
KEYHOLE FITTINGS
ROUND HEAD SCREWS
Figure 5 / Figura 5 / Schéma 5
6.
Pull the spring clip on the fi xture up and through the ceiling hole and
place module in the hole making sure the spring clips are holding securely.
(Figure 6)
7.
Turn the power back on. If the module doesn't illuminate within 5
seconds, turn power off, carefully remove the module and double check all
wiring and replace. (Figure 7)
Figure 7 / Figura 7 / Schéma 7
WARNING:
DO NOT PLACE YOUR HAND UNDERNEATH SPRING CLIP DURING
REMOVAL PROCESS. SNAPPING OF THE CLIPS CAN CAUSE INJU-
RIES TO THE HAND. (Figure 8)
DO NOT
PLACE YOUR
HAND
Figure 8 / Figura 8 / Schéma 8
DO NOT USE ANY OTHER DRIVER EXCEPT LITHONIA LIGHTING
DRIVER THAT IS INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE MODULES TO ONE DRIVER.
DO NOT OPEN THE MODULE AND SIDE PLATE OF THE REMOTE
DRIVER BOX - NO SERVICEABLE PARTS INSIDE.
Trouble Shooting Guide
If this fi xture fails to operate properly, use the guide
below to diagnose and correct the problem.
Verify that fi xture is wired properly.
Verify that fi xture is grounded correctly.
Verify that the line voltage at the fi xture is correct.
If further assistance is required, contact:
Technical Support at: (800) 705-SERV (7378)
This LED module does not require service or new bulbs to change.
Page 3
code for rigid attachment and
THROUGH
CEILING
HOLE
(MOUNTING
OPTIONAL)
Figure 6 / Figura 6 / Schéma 6
DO NOT
PLACE YOUR
HAND
PULL UP
Publicité
