Pro-Line II 71142M-3 Instructions De Montage

ÉTAPE 1 ÉTAPE 2
3
7R
1
2
ÉTAPE 4 ÉTAPE 5
6
3
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et vérifier que les quantités des
pièces reçues sont correctes.
ÉTAPE 1 Insérer cinq roulettes (2) dans la base (1), les pousser très fort jusqu'à ce que vous entendiez ou sentiez la roulette (2) s'enclencher. Insérer le vérin
pneumatique (3) dans la base (1).
ÉTAPE 2 Fixez les bras (7L et 7R) au coussin du siège (5) en utilisant trois vis longues (9) pour chaque bras (7). SERRER COMPLÈTEMENT TOUTES LES VIS
UTILISER LA CLÉ ALLEN (12).
ÉTAPE 3 Fixer le mécanisme (4) au coussin du siège (5) avec la flèche pointant vers l'avant du siège à l'aide de quatre vis courtes (8). SERRER
COMPLÈTEMENT TOUTES LES VIS UTILISER LA CLÉ ALLEN (12). Fixer le support du dossier (11) à l'arrière du mécanisme (4) à l'aide de quatre vis
courtes (8). COMPLÈTEMENT TOUTES LES VIS UTILISER LA CLÉ ALLEN (12).
ÉTAPE 4 Placer le siège assemblé sur le vérin pneumatique (3) et mettre de la pression.
ÉTAPE 5 Fixer la couverture plastique (10) au dossier (6).
ATTENTION: AVANT D'UTILISER LE FAUTEUIL, S'ASSURER D'AVOIR SERRÉ COMPLÈTEMENT TOUTES LES VIS.
71142M-3
CHAISE A DIRECTION AVEC LE DOSSIER
ET SIÈGE EN MAILLES
INSTRUCTIONS DE MONTAGE
ÉTAPE 3
9 8
5
7L
6
8
5
PART
1. Base . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Roulettes . . . . . . . . . . . . . . . . . . . . . . . .5
3. Vérin pneumatique . . . . . . . . . . . . . . . . .1
4. Mécanisme. . . . . . . . . . . . . . . . . . . . . . .1
5. Coussin du siège . . . . . . . . . . . . . . . . . .1
6. Dossier. . . . . . . . . . . . . . . . . . . . . . . . . .1
10
7. Bras 78L et 7R) . . . . . . . . . . . . . . . . . . .2
8. Vis courtes (M8 x 25) . . . . . . . . . . . . . . .8
9. Vis longues (M6 x 30) . . . . . . . . . . . . . .6
10. Couverture plastique . . . . . . . . . . . . . . .1
11. Support du dossier . . . . . . . . . . . . . . . .1
12. Clé Allen (non montré). . . . . . . . . . . . . .1
© Office Star Products novembre, 2023
4
4
11
QTÉ
PROLINE II LIMITED WARRANTY
ProLine II chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• Lifetime on component parts including pneumatic cylinder, control mechanism, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
• Leather is not warranted against routine scratching and scuffing, as leather is subject to minor blemishes in use.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and obtain return authorization. At it's
option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return freight on
components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. The 54666 is for persons weighing 300 lbs. or less. The 7103M, 7602R, 7605R, 7600R, 81108, 81308 & 81608 are for persons weighing 400 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal Wuse. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a five
year warranty on all parts applies. Fabric is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. All ProLine II are built to meet or exceed ANSI BIFMA standards.
It is the customer's responsibility to prepay freight on any components returned to the factory. Return freight on components covered by
warranty will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts.department@officestar.net, by Fax 1-909-930-5629, or
toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 3:30pm. Pacific Ti
71142M-3
MESH SEAT & BACK AND MANAGER'S CHAIR
OPERATING INSTRUCTIONS
FEATURES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and pull lever (1) up.To
lower seat height sit on chair and pull lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight.
• SEAT SLIDER ADJUSTMENT
To slide seat forward or backward, lift lever (2) up. Release
lever (2) to lock desired seat position.
• BACK ANGLE ADJUSTMENT
To adjust tilt angle, pull lever (3) up for free float, and push
lever (3) down to lock.
desired height is reached.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, lift lever (4) up to allow the arms to move up or
down freely and release lever (4) once the desired height is reached.
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts, screws and knobs are tight every three months or
as needed.
3 4. Dispose of packing material properly. Do not use plastic cover as head
covering. It may cause suffocation.
5. Do not use chair as a stepladder.
6. Use this chair for its intended purpose only.
2
7. Use mild detergent only for cleaning.
1
me.
down freely. Release the button (3) once the