NuTone LA225WH Directives D'installation Et D'utilisation

WESTMINSTER AND TWO-NOTE
WIRELESS CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 100 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
SLOT
"PUSH"
TO OPEN COVER
Figure 1
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with "+" side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
"SLIDE"
TO OPEN
Figure 3
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Orient chime face-down.
3. Press on battery compartment cover serrations and slide cover in
direction of triangular-arrow.
4. Remove battery compartment cover and set aside.
5. Insert three (3) 1.5V "AA" alkaline batteries (not supplied) into battery
compartment oriented as shown on back of battery compartment.
6. Slide battery compartment cover back onto chime until it snaps
securely into place.
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
3 - "AA" SIZE BATTERIES
Figure 4
"LEARN" PROCEDURE
Refer to Figure 5.
1. Set wireless pushbutton and chime next to each other.
2. Press and release "Learn" button on side of chime.
3. Confirm two (2) lower-tone beeps are heard to indicate entered
"Learn" mode.
4. Press and release wireless pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release "Learn" button
on side of chime (Note: Chime may not respond to this button being
pressed if it is too soon after chime-tone sounds).
8. Confirm two (2) higher-tone beeps are heard to indicate exited "Learn"
mode.
9. Press and release wireless pushbutton and confirm chime-tone hasn't
changed.
• Multiple wireless pushbuttons can be used with a single chime by
selecting different chime-tones for each wireless pushbutton.
• Chime can erase all "Learned" wireless pushbuttons by pressing
and holding "Learn" button on side of chime (two initial lower-tone
beeps will sound). Release "Learn" button on side of chime after
approximately 10 seconds when four (4) higher-tone beeps are heard.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8 to 1/4" wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 100-feet of each
other.
1. Place chime near its desired mounting location.
2. Select a level location and hold pushbutton in its desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
MODEL LA225WH
Page 1
LEARN BUTTON
Figure 5