Publicité
lid. Do not open the lid during boiling in kettle or immediately after boiling, because steam
coming out of lid can cause burns.
21. Move the kettle only by holding it by handle..
22. Never fill kettle above MAX level and below MIN level. It may cause damage of kettle.
23. Never switch on kettle without water.
24. Never use kettle without filter or with open cover (automatic shutdown will not work).
25. Descale your kettle regularly. Using kettle with heating element covered by scale may
cause damage.
26. Do not use aggressive detergents to wash the kettle housing - they can damage the
kettle or remove the markings.
27. The device is not designed to work with external schedulers or separate remote
control system.
28. Do not wash the base of the kettle directly in the water, just wipe with a dry cloth.
29. Children aged 3 to 8 years old can enable and disable the device only when it is in its
normal position of use, they are supervised or instructed on the safe use and understand
the resulting risks. Children aged 3 to 8 years old can not connect device, operate, clean
or maintain.
DESCRIPTION
1 - plastic lid
4 - handle
A- ON/OFF
USING THE ELECTRIC KETTLE
BEFORE FIRST USE: Fill up the kettle with water, boil and pour. Repeat three times. To remove possiblefactory smell..
1. Fill the kettle with water. Make sure that heating plate is fully immersed in water.Till minimum mark
2. Place the appliance on flat, even and heat resistant surface.
3. Plug the kettle to the 220-240V ~50/60Hz mains, press ON/OFF (A) switch. Indicator lamp will light.(A)
4. After boiling water the kettle will automatically switch off.
5. Before taking the kettle out of the base make sure it is switched OFF.
6. The kettle can manually be switched off any time by ON/OFF switch (A) at.
7. Keep lid closed during the boiling process. Or the kettle won't automatically switch off.
8. After boiling, time demanded for the thermostat to be ready is 2 minutes. After this time the kettle can be switched on again.
9. Regularly remove limestone sediment inside the kettle. Sediment may cause overheating of the kettle, shorten life cycle and cancel
guarantee. Use mixings available in household stores or apply citric acid.
10. Switching empty kettle, or with insufficient level of water, will cause automate switching off the kettle. Wait till cool down the kettle,
pour enough water and after few minutes switch the kettle on.
11 When the water is heated to the appropriate temperature, device signals this with two beeps.
12.Code E1 on LCD display warns user when the device is not on the basis of, or is not put properly.
13. The kettle is an electrical device and it is not designed to hold water or other liquids. After boiling, the water must be immediately
pour into another bowl. The water in the kettle after boiling can not stay longer than 10 minutes. Before each use, fill the kettle with
fresh water above the minimum and below the maximum level.
14. Holding down the button (A) for 3 seconds will turn off (OFF on the LCD display) the kettle, the LED (A) will flash.
BASICAL OPERATION:
SINGLE BOILING UP TO 100℃
Press the "A" key briefly, with the sound "di.", it starts working.
After the water boils, indicator turns off and the buzzer sends out a "di di" sound at the same time.
To stop cooking, press the button (A) ON/OFF
ADVANCED OPERATION:
WATER BOILING 40℃ - 90℃ WITHOUT THE KEEP WARM FUNCTION
Press "A" key, the buzzer will send out a "di" sound, the kettle will start boiling now, the LED (A) will flash.
After that Press"B" key once / twice / thrice / fourth /fifth / sixth /seven times, then the LCD display will show 40℃ / 50℃ / 60℃ / 70℃ /
80℃ /90℃ This means that it will stop heating when the water temperature reaches 40℃ / 50℃ / 60℃ / 70℃ / 80℃ /90℃
To stop, press the button (A)
KEEP WARM FUNCTION 100℃
Press the "A" key briefly, with the sound "di.", it starts working.
After that Press "D",with the buzzer sends out "di" sound, "D" button indicator light is on, and the kettle is in keep warm mode. The
indicator"D" light is still lit after water has finished the boiling and the kettle automatically. The keep warm function for 2 hours. When
switches to the water temperature decreases to 90℃ the kettle starts to boil again to 100℃ and repeats the operation for 2 hours.
To stop the keep warm function press the button (A)
2 - lid opening switch
5 - base
B - Temperature regulation
The LED (A) will flash.
The LED (A) will flash.
3 - housing
6 - anti-calc filter
C - Dechlorination function
4
7 - control panel
D- Keep warm function
Publicité
